agentVpcDomainPeerDetectionTimeout
DNOS-VPC-MIB ·
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.9
Object
column
r/w
Unsigned32
To configure the DCPDP reception timeout. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously.
Context
- MIB
- DNOS-VPC-MIB
- OID
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.9- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- agentVpcDomainConfigEntry
- Table
- agentVpcDomainConfigTable
- Siblings
- 12
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 700-14000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| agentVpcDomainIndex VPC Domain ID. | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.1 |
| agentVpcDomainPeerIpAddr To configure IP address of the peer VPC switch. This
configuration is used by the dual control plane detection
protocol (DCPDP) on the VPC switches.
NOTE: In order … | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.10 |
| agentVpcDomainSourceIpAddr To configure Self IP address of the VPC switch that is used as
the source IP by the dual control plane detection protocol (DCPDP)
on the VPC switches.
NOTE: In orde… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.11 |
| agentVpcDomainDcpdpUdpPort To configure the UDP port on which the VPC switch listens to
the DCPDP messages.
Configurable range is 1 to 65535. Default value is 50000.
NOTE: In order to set val… | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.12 |
| agentVpcDomainStatus Status of VPC Domain. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.13 |
| agentVpcDomainKeepalivePriority To configure the priority of the VPC switch. This value is used
for the VPC role election.
Configurable range is 1 to 255. The default value is 100.
Note: The VPC switch with lowe… | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.2 |
| agentVpcDomainKeepaliveTimeout To configure the peer keepalive timeout value (in seconds). If
an VPC switch does not receive keepalive messages from the peer
for this timeout value, it takes the decision to tra… | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.3 |
| agentVpcDomainKeepaliveMode To start/stop the keepalive state machine on the VPC device, if
VPC is globally enabled.
The following options are supported:
enable - Enable keepalive
disable - D… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.4 |
| agentVpcDomainPeerDetectionMode To start/stop the dual control plane detection protocol (DCPDP) on the
VPC switch.
The following options are supported:
enable - Enable the DCPDP on VPC switch
dis… | column | Enumeration | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.5 |
| agentVpcDomainSystemMac To configure the MAC address for the VPC domain. This mac-address
is used in the LACP PDUs and STP BPDUs
that are sent out on VPC member ports. For the VPC domain to use
the ma… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.6 |
| agentVpcDomainSystemPriority To configure the system priority for the VPC domain. This is used
in the LACP PDUs sent out on VPC member ports. System-priority
should be configured same on both the VPC peers.… | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.7 |
| agentVpcDomainPeerDetectionInterval To configure the DCPDP transmission interval.
NOTE: In order to set value for the object, need to set values for DCPDP
transmission interval and reception timeout simultaneously. | column | Unsigned32 | .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.8 |