agentVpcDomainKeepaliveTimeout

DNOS-VPC-MIB · .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.3
MIB view Table view

Object

column r/w Unsigned32 
To configure the peer keepalive timeout value (in seconds). If
an VPC switch does not receive keepalive messages from the peer
for this timeout value, it takes the decision to transition its
role (if required).
Configurable range is 2 to 15 seconds. Default value is 5 seconds.
Note: The keepalive state machine is not restarted if keepalive
priority is modified post election.

Context

MIB
DNOS-VPC-MIB
OID
.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.3
Type
column
Access
readwrite
Status
current
Parent
agentVpcDomainConfigEntry
Table
agentVpcDomainConfigTable
Siblings
12

Syntax

Unsigned32

Values & Constraints

Object Constraints
range: 2-15

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
agentVpcDomainIndex
VPC Domain ID.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.1
agentVpcDomainPeerIpAddr
To configure IP address of the peer VPC switch. This configuration is used by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order …
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.10
agentVpcDomainSourceIpAddr
To configure Self IP address of the VPC switch that is used as the source IP by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In orde…
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.11
agentVpcDomainDcpdpUdpPort
To configure the UDP port on which the VPC switch listens to the DCPDP messages. Configurable range is 1 to 65535. Default value is 50000. NOTE: In order to set val…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.12
agentVpcDomainStatus
Status of VPC Domain.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.13
agentVpcDomainKeepalivePriority
To configure the priority of the VPC switch. This value is used for the VPC role election. Configurable range is 1 to 255. The default value is 100. Note: The VPC switch with lowe…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.2
agentVpcDomainKeepaliveMode
To start/stop the keepalive state machine on the VPC device, if VPC is globally enabled. The following options are supported: enable - Enable keepalive disable - D…
columnEnumeration.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.4
agentVpcDomainPeerDetectionMode
To start/stop the dual control plane detection protocol (DCPDP) on the VPC switch. The following options are supported: enable - Enable the DCPDP on VPC switch dis…
columnEnumeration.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.5
agentVpcDomainSystemMac
To configure the MAC address for the VPC domain. This mac-address is used in the LACP PDUs and STP BPDUs that are sent out on VPC member ports. For the VPC domain to use the ma…
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.6
agentVpcDomainSystemPriority
To configure the system priority for the VPC domain. This is used in the LACP PDUs sent out on VPC member ports. System-priority should be configured same on both the VPC peers.…
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.7
agentVpcDomainPeerDetectionInterval
To configure the DCPDP transmission interval. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.8
agentVpcDomainPeerDetectionTimeout
To configure the DCPDP reception timeout. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously.
columnUnsigned32.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.200.1.9.1.9