dcRsvpProductLSPHoldingPriority
DC-RSVP-MIB ·
.1.3.6.1.4.1.629.10.6.1.1.1.19
Object
column
r/w
Integer32
The holding priority to apply to LSPs which are not signalling this parameter. 0 represents the highest priority, 7 the lowest. The value of this object must be numerically less or equal (so higher or equal priority) than the value of the holding priority object.
Context
- MIB
- DC-RSVP-MIB
- OID
.1.3.6.1.4.1.629.10.6.1.1.1.19- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dcRsvpProductEntry
- Table
- dcRsvpProductTable
- Siblings
- 71
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-7
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dcRsvpProductIndex The index of this dcRsvpProductEntry. This is the
HAF entity index passed on the entity create parameters. | column | DcRsvpIndex | .1.3.6.1.4.1.629.10.6.1.1.1.1 |
| dcRsvpProductRefreshMultiple The RSVP value, K, which is the number of unresponded Path
or Resv refresh attempts which must be made, spaced by
the refresh interval before the state is deemed to have
timed out… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.10 |
| dcRsvpProductRfrshSlewDenom The denominator of the fraction, SlewMax, which is the
maximum allowable increase in the refresh interval, R, to
prevent state timeout while changing R. R is increased by
this fr… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.11 |
| dcRsvpProductRfrshSlewNumerator The numerator of the fraction, SlewMax, which is the maximum
allowable increase in the refresh interval, R, to prevent
state timeout while changing R. R is increased by this
frac… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.12 |
| dcRsvpProductBlockadeMultiple The RSVP value, Kb, which is the number of refresh timeout
periods after which blockade state is deleted. | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.13 |
| dcRsvpProductSocketBufPoolSize The number of pre-reserved buffers available for sending
sockets data. This is used to pace the sockets data flows. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.14 |
| dcRsvpProductSwitchBufPoolSize The number of pre-reserved buffers available for programming
the switch. This is used to ensure programming operations do
not fail in buffer shortage conditions. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.15 |
| dcRsvpProductTeMibBufPoolSize The number of pre-reserved buffers available for signalling
with the DC-TPM entity supporting the instance of the TE-MIB. This is
used to ensure signals are not lost in buffer sh… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.16 |
| dcRsvpProductRoutingBufPoolSize The number of pre-reserved buffers available for route
queries. This is used to ensure re-routing of many LSPs does
not fail in buffer shortage conditions. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.17 |
| dcRsvpProductLSPSetupPriority The setup priority to apply to LSPs which are not
signalling this parameter. 0 represents the highest
priority, 7 the lowest. The value of this object must be
numerically more o… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.18 |
| dcRsvpProductASNumber The number identifying the autonomous system (AS) to which
this node belongs. | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.2 |
| dcRsvpProductAdminStatus The desired administrative state of the RSVP entity. | column | DcRsvpAdminStatus | .1.3.6.1.4.1.629.10.6.1.1.1.20 |
| dcRsvpProductOperStatus The current operational state of this instance of DC-RSVP. | column | DcRsvpOperStatus | .1.3.6.1.4.1.629.10.6.1.1.1.21 |
| dcRsvpProductRowStatus Used to create and delete a DC-RSVP Product Table entry.
When this object is set to 'active', only the
dcRsvpProductAdminStatus object in the row may be modified. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.629.10.6.1.1.1.22 |
| dcRsvpProductLsrIndex The index of the DC-LMGR product instance which this
DC-RSVP is to join to as its LDB interface provider. If
this value is not specified, or the value of this object
is 0, DC-RSV… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.23 |
| dcRsvpProductTeMibIndex The index of the DC-TPM entity (which supports the TE-MIB) with
which this DC-RSVP entity is to join to as its LRA interface
provider. If this value is not specified, or the value… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.24 |
| dcRsvpProductMultiStackSupport A flag to indicate if multiple RSVP stacks are present
in the same system as the current one and, if so, how
they are supported. If set to PHOP, Path messages are
forwarded to DC… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.25 |
| dcRsvpProductUseHopByHop A flag to indicate that DC-RSVP should use the hop by hop
addressing scheme for PATH and PATH-TEAR messages it
sends. If set then the IP addresses used in the IP header
of PATH m… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.26 |
| dcRsvpProductUseNotify A flag to indicate that DC-RSVP should attempt to insert
a Notify Request object in all Path requests that it sends
as ingress and all Resv requests that it sends as egress.
The p… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.27 |
| dcRsvpProductNotifyRRDecay The percentage increase in the rapid retransmission
interval for each consecutive unacknowledged RSVP Notify
message. A value of 0 indicates a constant retransmission
rate. | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.28 |
| dcRsvpProductNotifyRRInterval The interval in milliseconds before a Notify message is
first resent if no acknowledgement is received. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.29 |
| dcRsvpProductSenderTTL The TTL set on messages originating at this node. A value
of 0 indicates this number is determined by other means. | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.3 |
| dcRsvpProductNotifyRRLimit The maximum number of times a Notify message is resent if
no acknowledgement is received. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.30 |
| dcRsvpProductAllowIPEncap A flag to indicate that DC-RSVP should support the use of
IP encapsulation of RSVP packets, which are required for
out-of-band signaling. If set, then DC-RSVP will accept
incomin… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.31 |
| dcRsvpProductProtocolExtensions Specifies which extensions to the standard RSVP-TE protocol
are enabled. For fully standards-compliant behavior, set
this parameter to zero (no bits set). To enable specific
non… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.32 |
| dcRsvpProductPSRFlags This field is used by DC-RSVP to determine whether it
should set the Path State Removed flag on a PathErr (and
therefore remove corresponding state and generate a
PathTear). Each… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.33 |
| dcRsvpProductInitPathRRDecay The percentage increase in the rapid
retransmission interval for each consecutive
unacknowledged RSVP Initial Path message. A value of 0
indicates a constant retransmission rate.… | column | Integer32 | .1.3.6.1.4.1.629.10.6.1.1.1.34 |
| dcRsvpProductInitPathRRInterval The rapid retransmission interval in milliseconds before
an Initial Path message is first resent if no
acknowledgement is received.
A Path message is treated as an … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.35 |
| dcRsvpProductInitPathRRLimit The maximum number of times an Initial Path message is
resent if no acknowledgement is received.
A Path message is treated as an initial Path if it is the
Path mess… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.36 |
| dcRsvpProductEnableUni A flag to indicate whether the local node supports UNI
signaling messages. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.37 |
| dcRsvpProductRestartCapable A flag to indicate whether the local node should advertise
itself as restart capable. This should be set to AMB_TRUE
if fault-tolerance is enabled in DC-MPLS or if the node
suppo… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.38 |
| dcRsvpProductRestartTime The time in milliseconds that the local node takes to
restart RSVP-TE and the communication channel used for
RSVP communication. This is advertised to neighbors in
the Restart_Ca… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.39 |
| dcRsvpProductMinTimerPeriod The minimum granularity to allow an internal timer to be
set in the DC-RSVP product code. | column | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.4 |
| dcRsvpProductRecoveryTime The period of time in milliseconds that the local node
would like neighbors to take to resyncronize RSVP and MPLS
forwarding information after the re-establishment of Hello
connec… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.40 |
| dcRsvpProductMinPeerRestart The mininum period of time in milliseconds that RSVP
should wait for a restart capable neighbor to regain
Hello connectivity before invoking procedures related to
communication lo… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.41 |
| dcRsvpProductGracefulDelTimeout The time in milliseconds that DC-MPLS will wait for
graceful deletion to complete before the forced deletion
procedure is used instead. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.42 |
| dcRsvpProductEgressDelBehavior Specifies the action that an egress node should take in
the graceful deletion procedure on receipt of a Path
message containing an Admin Status object with the D
and R bits set. … | column | Enumeration | .1.3.6.1.4.1.629.10.6.1.1.1.43 |
| dcRsvpProductEnabUniConnSplicing A flag to indicate whether UNI-N nodes should allow the
splicing of UNI connections with proprietary ON
connections. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.44 |
| dcRsvpProductFastRerouteCaps Specifies what fast reroute capabilities are enabled
on this node. This field is only valid if the fast
reroute extension is enabled in the
dcRsvpProductProtocolExtensions field … | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.45 |
| dcRsvpProductFastRroutBkpRtryInt When this node is a PLR, this field specifies the period
that the node should wait before retrying the setup of a
backup LSP which failed last time because no route was
available.… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.46 |
| dcRsvpProductErrorActionFlags This field is used by DC-RSVP to determine whether it
should take any special action following certain types of
local errors. Each bit of this flags field corresponds to
an error… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.47 |
| dcRsvpProductEnableNni A flag to indicate whether the local node supports NNI
signaling messages. | column | Enumeration | .1.3.6.1.4.1.629.10.6.1.1.1.48 |
| dcRsvpProductBehaviorFlags Specifies some detailed aspects of the behavior of
DC-RSVP. This field may be changed while _admin_status_
is AMB_ADMIN_STATUS_UP.
- enableTTLMatch: Whether to dis… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.49 |
| dcRsvpProductAPIIfIndex Management assigned interface identifier for the (internal) LRAPI
interface between RSVP and DC-TPM components. This must be unique in
the interface index namespace of the node -… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.629.10.6.1.1.1.5 |
| dcRsvpProductLabelSetStyle Specifies the style of LABEL_SET object that should be
used. RFCs 3741 and 3743 are unclear whether the
LABEL_SET object should include LABEL headers. The
correct interpretation… | column | Enumeration | .1.3.6.1.4.1.629.10.6.1.1.1.50 |
| dcRsvpProductLabelSetOperStatus The current operational status of Label Set style.
- excludeLabelHeader: The LABEL_SET object contains
concatenated LABEL values without the object headers.
- in… | column | Enumeration | .1.3.6.1.4.1.629.10.6.1.1.1.51 |
| dcRsvpProductLabelSetTrapEnable This object is used to enable traps for the Label
Set style oper_status object. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.52 |
| dcRsvpProductLabelSetChngAct Specifies the action to take when the value of
dcRsvpProductLabelSetStyle is changed.
- leaveLSPs: All nodes should suppress refreshes and
switch to the new format… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.53 |
| dcRsvpProductExtPrtAdminStatus The desired operational state of support for the extended
PROTECTION object defined in
draft-lang-ccamp-gmpls-recovery-e2e-signaling.
Support for end-to-end signall… | column | DcRsvpAdminStatus | .1.3.6.1.4.1.629.10.6.1.1.1.54 |
| dcRsvpProductUniIncSonetProfile This field is obsolete. The value in this field is
ignored by DC-RSVP for Test and Set commands. This field is
always set to 0 for Get responses. | column | Unsigned32 | .1.3.6.1.4.1.629.10.6.1.1.1.55 |
| dcRsvpProductFrrFacAdminStatus Specifies whether backup LSPs can be put in place for LSPs
requesting FRR using the facility method.
Setting this to UP means that LSPs that request FRR using
the f… | column | DcRsvpAdminStatus | .1.3.6.1.4.1.629.10.6.1.1.1.56 |
| dcRsvpProductFrrFacOperStatus The current operational status for FRR Facility support.
When this is UP backup LSPs will be put in place, when this
is down backup LSPs will not be put in place and there will
be… | column | DcRsvpOperStatus | .1.3.6.1.4.1.629.10.6.1.1.1.57 |
| dcRsvpProductIpv6AdminStatus Specifies whether the local node supports IPv6 LSPs.
Setting this to UP means that this node supports IPv6 LSPs
being set up to, from and through this node.
… | column | DcRsvpAdminStatus | .1.3.6.1.4.1.629.10.6.1.1.1.58 |
| dcRsvpProductIpv6OperStatus The current operational status for IPv6 support. When
this is UP IPv6 LSPs can be set up to from or through this
node. When this is down there will be no active IPv6 LSPs. | column | DcRsvpOperStatus | .1.3.6.1.4.1.629.10.6.1.1.1.59 |
| dcRsvpProductAPIAddress Management assigned IP address used to identify the (internal) LRAPI
interface between RSVP and DC-TPM components.
The configured API address MUST not be a real address in the net… | column | OctetString | .1.3.6.1.4.1.629.10.6.1.1.1.6 |
| dcRsvpProductAPIIpv6Address Management assigned IPv6 address used to identify the
(internal) LRAPI interface between RSVP and DC-TPM
components.
The configured API IPv6 address MUST not be a r… | column | IPV6-TCIpv6Address | .1.3.6.1.4.1.629.10.6.1.1.1.60 |
| dcRsvpProductExtPrtOperStatus The current operational state of support for the extended
PROTECTION object defined in
draft-lang-ccamp-gmpls-recovery-e2e-signaling. | column | DcRsvpOperStatus | .1.3.6.1.4.1.629.10.6.1.1.1.61 |
| dcRsvpProductRROHopType The type of Recorded Route hop that DC-RSVP will insert on
any messages requesting Recorded Route information.
DC-RSVP uses the same hop type on all outgoing messages.
If the hop … | column | Enumeration | .1.3.6.1.4.1.629.10.6.1.1.1.62 |
| dcRsvpProductBfdIndex The index of the BFD product instance which this
DC-RSVP is to join to as its BFD interface provider. If
the value of this object is 0, DC-RSVP will not attempt to
join to a BFD … | column | DC-MASTER-TCNumericIndexOrZero | .1.3.6.1.4.1.629.10.6.1.1.1.63 |
| dcRsvpProductBfdBufPoolSize The number of pre-reserved buffers available for BFD
interface messages. This is used to ensure that the
establishment of many BFD sessions does not fail in buffer
shortage condi… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.64 |
| dcRsvpProductLspAttrAdminStatus Specifies whether the local node supports the
LSP_ATTRIBUTES object.
Setting this to UP means that this node supports LSPs with
the LSP_ATTRIBUTES object being set … | column | DcRsvpAdminStatus | .1.3.6.1.4.1.629.10.6.1.1.1.65 |
| dcRsvpProductLspAttrOperStatus The current operational state of support for the
LSP_ATTRIBUTES object. | column | DcRsvpOperStatus | .1.3.6.1.4.1.629.10.6.1.1.1.66 |
| dcRsvpProductI3Index The index of the I3 entity with which this DC-RSVP entity
is to join to as its I3 interface provider. If this value
is not specified, DC-RSVP will use the
dcRsvpProductLsrIndex v… | column | DC-MASTER-TCNumericIndexOrZero | .1.3.6.1.4.1.629.10.6.1.1.1.67 |
| dcRsvpProductSckIndex The index of the SCK entity with which this DC-RSVP entity
is to join to as its SCK interface provider. If this
value is not specified, DC-RSVP will use the
dcRsvpProductIndex as… | column | DC-MASTER-TCNumericIndexOrZero | .1.3.6.1.4.1.629.10.6.1.1.1.68 |
| dcRsvpProductNhrIndex The index of the NHR entity with which this DC-RSVP entity
is to join to as its NHR interface provider. If this
value is not specified, DC-RSVP will use the
dcRsvpProductLsrIndex… | column | DC-MASTER-TCNumericIndexOrZero | .1.3.6.1.4.1.629.10.6.1.1.1.69 |
| dcRsvpProductAPIRefreshInterval This field is now deprecated. | column | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.7 |
| dcRsvpProductWaitForHellos Specifies whether DC-RSVP should suppress sending of Path
messages if gracefully restarting and there is no Hello
session up to the next hop.
If a Path message is s… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.70 |
| dcRsvpProductForcePEOnEgrDel Forces DC-RSVP to send a PathErr message upstream when
carrying out forced deletion of an LSP at the egress node.
If this field is AMB_TRUE then DC-RSVP will always send a
PathErr… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.629.10.6.1.1.1.71 |
| dcRsvpProductFastRrtBkpSetupInt When this node is a PLR, this field specifies the maximum
period that the node should wait on initiating the setup
of a backup LSP before sending a Resv message upstream for
the p… | column | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.72 |
| dcRsvpProductLocalRepairDelay This object is used to set the delay between detection of a
path error and instigation of local repair procedures. This
allows local routing updates to converge. A value of 0
in… | column | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.8 |
| dcRsvpProductRefreshInterval This RSVP value, R, which is used to set the average
interval between refresh path and resv messages.
Note : If values for the if_refresh_interval and if_refresh_multiple
are con… | column | milliseconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.629.10.6.1.1.1.9 |
Notification Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| MELLANOX-XSTP-MIBmellanoxXstpId MST Instance identifier or VLAN ID in case of PVRST+. | column | Unsigned32 | .1.3.6.1.4.1.33049.13.1.2.1.1.1 |
| MELLANOX-XSTP-MIBmellanoxXstpPortNum Number of the Bridge Port | column | Unsigned32 | .1.3.6.1.4.1.33049.13.1.2.2.1.2 |
| MELLANOX-XSTP-MIBmellanoxXstpPortState The current state of the Port (i.e., Disabled,
Listening, Learning, Forwarding, or Blocking), for the STI. | column | Enumeration | .1.3.6.1.4.1.33049.13.1.2.2.1.3 |