dsAdslLineConfProfileExtnMaxDCo
DASAN-ADSL-MIB ·
.1.3.6.1.4.1.6296.9.5.1.1.16.1.30
Object
column
r/w
Enumeration
This object is used to indicate Maximum interleaving depth supported by the customer's hardware.
Context
- MIB
- DASAN-ADSL-MIB
- OID
.1.3.6.1.4.1.6296.9.5.1.1.16.1.30- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsAdslLineConfProfileExtnEntry
- Table
- dsAdslLineConfProfileExtnTable
- Siblings
- 27
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | dsAdslLineConfProfileExtnTable64 |
4096 | dsAdslLineConfProfileExtnTable128 |
8192 | dsAdslLineConfProfileExtnTable256 |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsAdslLineConfProfileName This object is used by the line configuration table in order to identify a row of this table. | column | OctetString | .1.3.6.1.4.1.6296.9.5.1.1.16.1.1 |
| dsAdslLineConfProfileExtnRxBinAdjust Employs Rx Start/End bin settings. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.10 |
| dsAdslLineConfProfileExtnStandard Preferred standard compliance. Outcome is dependent upon standard support of the remote unit.GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.13 |
| dsAdslLineConfProfileExtnTxPowerAttenuation Specifies value of Tx power attenuation. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.15 |
| dsAdslLineConfProfileExtnRsFastOvrhdDown Sets the percentage overhead for the downstream-fast buffer. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.17 |
| dsAdslLineConfProfileExtnIntCorrectionDown This parameter sets the correction time for the downstream interleaved buffer.RS can also be disabled. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.18 |
| dsAdslLineConfProfileExtnRsFastOvrhdUp Sets the 4576014verhead for the upstream-fast buffer. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.19 |
| dsAdslLineConfProfileExtnAnnexType This parameter is set as per annex compliance of the code release. GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.26 |
| dsAdslLineConfProfileExtnRsIntCorrectionUp Sets the correction time for the upstream-interleaved buffer. RS can also be disabled. The Default Value for ADSL+ is 3. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.3 |
| dsAdslLineConfProfileExtnAdvertisedCapabilities Controls if the CO will attempt to startup using alternate standards if the CPE does not support ADSL+. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.32 |
| dsAdslLineConfProfileExtnPsdMaskType Selects the PSD mask option to be used. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.33 |
| dsAdslLineConfProfileExtnLineDmtConfMode Selects if there is overlap or no overlap of bins. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.34 |
| dsAdslLineConfProfileExtnLineType This object is used to configure the ADSL physical line mode. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.4 |
| dsAdslLineConfProfileExtnUpstreamPSD This object sets the upstream PSD to be either extended or standard. Used for GSpan Plus only. | column | Enumeration | .1.3.6.1.4.1.6296.9.5.1.1.16.1.41 |
| dsAdslLineConfProfileExtnPMMode PM-related parameter used by the ATU-C to set the allowed link states. | column | Bits | .1.3.6.1.4.1.6296.9.5.1.1.16.1.42 |
| dsAdslLineConfProfileExtnPML0Time PM configuration parameter, related to the L2 low power state. This parameter represents the minimum time (in seconds) between an exit from the L2 state and the next entry into th… | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.43 |
| dsAdslLineConfProfileExtnPML2Time PM configuration parameter, related to the L2 low power state. This parameter represents the minimum time (in seconds) between an Entry into the L2 state and the first Power Trim … | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.44 |
| dsAdslLineConfProfileExtnPML2ATPR PM configuration parameter, related to the L2 low power state. This parameter represents the maximum aggregate transmit power reduction (in dB) that can be performed through a sin… | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.45 |
| dsAdslLineConfProfileExtnPML2Rate PM configuration parameter, related to the L2 low power state. This parameter specifies the minimum net data rate during the low power state (L2). The data rate is coded in bit/s. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.46 |
| dsAdslLineConfProfileExtnTxEndBin Highest bin number allowed for Tx signal. The Range & default for ADSL+ is 0x06 - 0x1ff and 0x1ff respectively. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.5 |
| dsAdslLineConfProfileExtnTxStartBin Lowest bin number allowed for Tx signal.The Range for ADSL+ is 0x06 - 0x1ff. The Default for Annex B is 0x40 respectively. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.6 |
| dsAdslLineConfProfileExtnAtucConfMinINP Parameter used to specify the minimum impulse noise protection
for the downstream bearer channel. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.63 |
| dsAdslLineConfProfileExtnPML2EntryThresholdRate PM configuration parameter, related to the L2 low power state.
This parameter specifies the downstream data rate threshold
that triggers autonomous entry into low power state (L2)… | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.64 |
| dsAdslLineConfProfileExtnPML2ExitThresholdRate PM configuration parameter, related to the L2 low power state.
This parameter specifies the downstream data rate threshold
that triggers autonomous exit from low power state (L2).… | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.65 |
| dsAdslLineConfProfileExtnPML2EntryRateMinTime PM configuration parameter, related to the L2 low power state.
This parameter specifies the minimum interval of time that the
net data rate for the bearer channel should stay belo… | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.66 |
| dsAdslLineConfProfileExtnRxStartBin Lowest bin number allowed for Rx signal. The Range for ADSL+ is 0x01 - 0x1ff. The default for Annex B is 0x01. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.8 |
| dsAdslLineConfProfileExtnRxEndBin Highest bin number allowed for Rx signal. The Range and default value for ADSL+ is 0x01 - 0x1ff and 0x1d respectively. | column | Integer32 | .1.3.6.1.4.1.6296.9.5.1.1.16.1.9 |