wanDs1ExtensionsCFADuration
CTRON-WAN-MIB ·
.1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.5
Object
column
mandatory
r/w
Integer32
The length of time (in seconds), that the ds1 port will remain in the Carrier Failure Alarm state after the alarm condition has cleared.
Context
- MIB
- CTRON-WAN-MIB
- OID
.1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.5- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- wanDs1ExtensionsEntry
- Table
- wanDs1ExtensionsTable
- Siblings
- 17
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-15
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wanDs1ExtensionsEntryIndex mandatory A unique value for each ds1 physical port on the platform. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.1 |
| wanDs1ExtensionsBertCurrentResults mandatory Indicates the results of the testing for the
last completed sampling period. A non-negative
number is the error rate in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.10 |
| wanDs1ExtensionsBertCumulativeResults mandatory Indicates the total number of errors since the
testing was enabled. It is not a rate. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.11 |
| wanDs1ExtensionsBertPeakResults mandatory Indicates the highest value of
wanDs1ExtensionsBertCurrentResults since the testing
was enabled. A non-negative number is the error rate
in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.12 |
| wanDs1ExtensionsBertAverageResult mandatory Indicates the average value of
wanDs1ExtensionsBertCurrentResults since the testing
was enabled. A non-negative number is the error rate
in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.13 |
| wanDs1ExtensionsBertTestPattern mandatory This object is used to specify the pattern of the
test data. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.14 |
| wanDs1ExtensionsBertSamplePeriod mandatory This object is the duration of time in seconds at
which the current test results will be periodically
written to wanDs1ExtensionsBertCurrentResults. The
range is 1 to 3600, with… | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.15 |
| wanDs1ExtensionsBertNumPeriods mandatory The number of sampling periods that have elapsed
during the current test run. | column | RFC1155-SMICounter | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.16 |
| wanDs1ExtensionsBertTestTraps mandatory This object is used to enable or disable the sending
of a trap at the conclusion of the measurement period.
The trap will contain the information described by
ctDs1BertCurrentResu… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.17 |
| wanDs1ExtensionsBertDataStatus mandatory This object provides the operating status of the
transmission of test data packets. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.18 |
| wanDs1ExtensionsNumInterfaces mandatory The number of interfaces on this physical port. This
number indicates the number of entries this physical port
uses in the ifTable. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.2 |
| wanDs1ExtensionsToggleFracTable mandatory Setting this object to 1 will cause the Ds1 Fractional Table
to be updated with the new values, as entered.
Setting this object to 2, will cause the Ds1 Fractional Table
to view a… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.3 |
| wanDs1ExtensionsLineBuildOut mandatory The line build out setting for this ds1 physical port.
Unknown indicates that the setting is neither readable or
writable. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.4 |
| wanDs1ExtensionsDIEnable mandatory Enables or disables Drop and Insert functionality on a
D/I WPIM. If enabled, all zero assigned timeslots will
designate D/I interface channels, if disabled all zero
channels wi… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.6 |
| wanDs1ExtensionsTotalValidIntervals mandatory The number of previous intervals for which
valid data was collected for the DS1 mib, which
is currently RFC1406. This counter is similar to
RFC1406 dsx1ValidIntervals except … | column | RFC1155-SMICounter | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.7 |
| wanDs1ExtensionsBertTestMode mandatory This object is used to request that a type of
process be in control of the testing function.
This is used to differentiate between automated test
procedures and those manually co… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.8 |
| wanDs1ExtensionsBertRun mandatory Controls the sending of test data over this physical
port. The data is a pattern described by
wanDs1ExtensionsBertTestPattern. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.1.2.1.1.9 |