wanDs1ExtensionsBertDataStatus
CTRON-REMOTE-ACCESS-MIB ·
.1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.18
Object
column
mandatory
Enumeration
This object provides the operating status of the transmission of test data packets.
Context
- MIB
- CTRON-REMOTE-ACCESS-MIB
- OID
.1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.18- Type
- column
- Access
- readonly
- Status
- mandatory
- Parent
- ctDs1ExtensionsEntry
- Table
- ctDs1ExtensionsTable
- Siblings
- 17
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | idle |
2 | waitingForLink |
3 | waitingForLoopback |
4 | running |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ctDs1ExtensionsEntryIndex mandatory A unique value for each ds1 physical port on the platform. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.1 |
| wanDs1ExtensionsBertCurrentResults mandatory Indicates the results of the testing for the
last completed sampling period. A non-negative
number is the error rate in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.10 |
| wanDs1ExtensionsBertCumulativeResults mandatory Indicates the total number of errors since the
testing was enabled. It is not a rate. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.11 |
| wanDs1ExtensionsBertPeakResults mandatory Indicates the highest value of
wanDs1ExtensionsBertCurrentResults since the testing
was enabled. A non-negative number is the error rate
in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.12 |
| wanDs1ExtensionsBertAverageResult mandatory Indicates the average value of
wanDs1ExtensionsBertCurrentResults since the testing
was enabled. A non-negative number is the error rate
in bits per million bits. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.13 |
| wanDs1ExtensionsBertTestPattern mandatory This object is used to specify the pattern of the
test data. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.14 |
| wanDs1ExtensionsBertSamplePeriod mandatory This object is the duration of time in seconds at
which the current test results will be periodically
written to wanDs1ExtensionsBertCurrentResults. The
range is 1 to 3600, with… | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.15 |
| wanDs1ExtensionsBertNumPeriods mandatory The number of sampling periods that have elapsed
during the current test run. | column | RFC1155-SMICounter | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.16 |
| wanDs1ExtensionsBertTestTraps mandatory This object is used to enable or disable the sending
of a trap at the conclusion of the measurement period.
The trap will contain the information described by
ctDs1BertCurrentResu… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.17 |
| ctDs1ExtensionsNumInterfaces mandatory The number of interfaces on this physical port. This
number inidicates the number of entries this physical port
uses in the ifTable. | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.2 |
| ctDs1ExtensionsToggleFracTable mandatory Setting this object to 1 will cause the Ds1 Fractional
Table to be updated with the new values, as entered.
Setting this object to 2, will cause the Ds1 Fractional… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.3 |
| ctDs1ExtensionsLineBuildOut mandatory The line build out setting for this ds1 physical port.
Unknown indicates that the setting is neither readable or
writable. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.4 |
| ctDs1ExtensionsCFADuration mandatory The length of time (in seconds), that the ds1 port will
remain in the Carrier Failure Alarm state after the
alarm condition has cleared. For those Ds1 ports not
supporting Carrie… | column | Integer32 | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.5 |
| ctDs1ExtensionsDIEnable mandatory Enables or disables Drop and Insert functionality on a
D/I WPIM. If enabled, all zero assigned timeslots will
designate D/I interface channels, if disabled all zero
channels wi… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.6 |
| ctDs1ExtensionsTotalValidIntervals mandatory The number of previous intervals for which
valid data was collected for the DS1 mib, which
is currently RFC1406. This counter is similar to
RFC1406 dsx1ValidIntervals except … | column | RFC1155-SMICounter | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.7 |
| wanDs1ExtensionsBertTestMode mandatory This object is used to request that a type of
process be in control of the testing function.
This is used to differentiate between automated test
procedures and those manually co… | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.8 |
| wanDs1ExtensionsBertRun mandatory Controls the sending of test data over this physical
port. The data is a pattern described by
wanDs1ExtensionsBertTestPattern. | column | Enumeration | .1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.9 |