configPowerDc2
CTATX-MIB ·
.1.3.6.1.4.1.97.3.3.1.9
Object
scalar
mandatory
Enumeration
Whether the second power supply provides DC voltage.
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | dc-good |
2 | dc-bad |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| configFatalErr mandatory This is a 32 byte array which contains information about
the cause of the previous system reset. This will
describe the circumstances which forced the system
software to perform a… | scalar | OctetString | .1.3.6.1.4.1.97.3.3.1.1 |
| configPowerPresent1 mandatory Whether the first power supply is present. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.10 |
| configPowerPresent2 mandatory Whether the second power supply is present. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.11 |
| configAlarmDynamic mandatory Whether changes in dynamic parameters (except for the
dynamically learned addresses) should cause enterprise
specific trap PDUs to be generated. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.12 |
| configAlarmAddresses mandatory Whether changes in the dynamically learned addresses
should cause enterprise specific trap PDUs to be
generated. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.13 |
| configStorageFailure mandatory Whether the ES/1's storage facility for its configuration
parameters has failed (the ES/1 may not be able to reboot
after such a failure). | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.14 |
| configAuthenticationFailure mandatory All nulls, or the IP source address within the last SNMP
PDU which caused an SNMP authentication failure. | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.97.3.3.1.15 |
| configFddiPriority mandatory Priority to use when forwarding packets to any FDDI port
from any non-FDDI port. | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.16 |
| configTprPriority mandatory Priority to use when forwarding packets to any Token-Ring
port from any non-Token-Ring port. | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.17 |
| configDumpModule mandatory Flag to select the module to dump on a crash.
If set to a value of 1 to 7 the relevant module's
memory will be sent to the UART port on detecting
a fatal error situation. A value … | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.19 |
| configAnyPass mandatory The authentication password (0-24 bytes) which must match
the community name in an SNMP PDU, in order for the
operation to be performed. A zero length password
indicates that any … | scalar | OctetString | .1.3.6.1.4.1.97.3.3.1.2 |
| configDumpStart mandatory Starting address of memory to dump upon detecting
a fatal error. | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.20 |
| configDumpEnd mandatory Ending address of memory to dump upon detecting
a fatal error. | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.21 |
| configGetPass mandatory The authentication password (0-24 bytes) which must match
the community name in an SNMP Get PDU (except for Debug
or password parameters). A zero length password indicates
that an… | scalar | OctetString | .1.3.6.1.4.1.97.3.3.1.3 |
| configNMSAddress mandatory The address of the NMS to which Trap PDUs are to be sent.
A value of zero indicates that Trap PDUs should be sent
to the NMS last heard from. | scalar | RFC1155-SMIIpAddress | .1.3.6.1.4.1.97.3.3.1.4 |
| configFunctions mandatory A bit field which describes the software functions
supported by this ES/1. The possible values are:
0x0001 NMS, 0x0002 TBRIDGE, 0x0004 SBRIDGE,
0x0008 MESH, 0x0010 IPROU… | scalar | Integer32 | .1.3.6.1.4.1.97.3.3.1.5 |
| configPowerAc1 mandatory Whether the first power supply has AC input. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.6 |
| configPowerAc2 mandatory Whether the second power supply has AC input. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.7 |
| configPowerDc1 mandatory Whether the first power supply provides DC voltage. | scalar | Enumeration | .1.3.6.1.4.1.97.3.3.1.8 |