cmdot11CurrentChannel
CM-dot11plus-MIB ·
.1.3.6.1.4.1.1166.1.19.51.1.5.1.2
Object
Reading this object displays the current channel number the access point is operating in. It displays 0 if the Wireless interface is disabled.
Context
- MIB
- CM-dot11plus-MIB
- OID
.1.3.6.1.4.1.1166.1.19.51.1.5.1.2- Type
- scalar
- Access
- readonly
- Status
- deprecated
- Parent
- cmdot11MgmtBase
- Siblings
- 10
Syntax
SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cmdot11OperMode deprecated Setting this object to enable(1) enables the Wireless interface. Setting this object to
disable(2) disables the Wireless interface. | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.1 |
| cmdot1154gNetMode deprecated Controls and reflects the behavior of the device with regards to which
802.11 mode is used. If set to mode54gLRS(5), the device
will interoperate with the widest variety of 54g a… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.10 |
| cmdot11MulticastRate deprecated Controls the physical layer transmission rate used for Multicast traffic on the
Wireless interface. The defined rates are the theoretical physical link rate.
Actual data rates w… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.100 |
| cmdot11NMode deprecated Used to enable/disable 802.11n operation.
'Auto' is used to enable 802.11n operation; the Access Point will detect which
stations are out there and operate in the proper mode.
'… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.16 |
| cmdot11NPhyRate deprecated Used to specify the 802.11n PHY transmission rate.
'Auto' is used to allow the Access Point to dynamically adapt
to the environment and transmit using the fastest data rate
for … | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.17 |
| cmdot11NBand deprecated Selects the wireless frequency band (2.4 GHz or 5 GHz) the Access Point will operate in.
Note: This MIB object is only valid for products supporting 802.11n. | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.18 |
| cmdot11NBandWidth deprecated Specifies the channel width (20 MHz or 20/40 MHz) to be used by the Access Point.
When 20/40MHz is selected 802.11n clients experience improved throughput
using 40 MHz, while lega… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.19 |
| cmdot11NSideBand deprecated When bonded channels (40 MHz) are used this object specifies if the
control (primary) channel is in the lower or upper 20 MHz band of the
bonded 40 MHz channel.
Note: This MIB o… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.20 |
| cmdot11NProtection deprecated Determines if protection will be turned on or off for 802.11n mode.
When set to auto, the Access Point will enable protection to allow
802.11n clients to co-exist with 802.11a/b/g… | scalar | Enumeration | .1.3.6.1.4.1.1166.1.19.51.1.5.1.21 |
| cmdot11ChannelSetting deprecated This object sets the current channel number (802.11g) or control
channel (802.11n).
If set to (0), the AP will be put in auto-channel mode where
it automatically sc… | scalar | Unsigned32 | .1.3.6.1.4.1.1166.1.19.51.1.5.1.3 |