bbChanTestStateCPESide
CISCO-WAN-BBIF-ATM-CONN-MIB ·
.1.3.6.1.4.1.351.110.5.2.7.1.1.1.44
Object
column
Enumeration
This shows the state of the test When you add a connection then the chanTestState becomes notinprogress and when you select any test, it would go to inprogress state and after it completes the test, it will go to failed or passed state. 1 = Passed 2 = Failed 3 = In Progress 4 = Not In Progress
Context
- MIB
- CISCO-WAN-BBIF-ATM-CONN-MIB
- OID
.1.3.6.1.4.1.351.110.5.2.7.1.1.1.44- Type
- column
- Access
- readonly
- Status
- current
- Parent
- bbChanCnfGrpEntry
- Table
- bbChanCnfGrpTable
- Siblings
- 52
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | passed |
2 | failed |
3 | inprogress |
4 | notinprogress |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| bbChanCnfNum This identifies a channel on the PXM logical interface, used as
PXM port. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.1 |
| bbChanVci VCI for the connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.10 |
| bbChanUpcEnable enables/disables UPC for Ingress cells. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.11 |
| bbChanUpcPCR PCR(0+1), Peak Cell Rate, specifies an upper bound on
rate at which traffic can be submitted on an ATM
connection. This object applies to the First Leaky
Bucket for leaving cells … | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.12 |
| bbChanUpcCDVT Compliant Cell Delay Variation. Also known as
CDVT(0+1), Cell Delay Variation Tolerance, which
specifies the maximum time period for accumulated
violations of cell-arrival time pa… | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.13 |
| bbChanUpcSCR SCR, Sustainable Cell Rate, is an upper bound on the
conforming average rate of an ATM connection, over
time scales which are long relative to those for which
the PCR is defined. … | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.14 |
| bbChanUpcMBS Maximum Burst Size (MBS). Also known as Compliant Burst Size (CBS).
. Units: cells
. Applicable connection types:
. VBR, ABR
. Default: 1000
. Range : 1-5000000 | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.15 |
| bbChanGcra1Action GCRA1 Action.
1 = No Action
2 = Tag Untagged cells
3 = Tag untagged cells and discard tagged cells
4 = Discard all (0+1) non-comforming cells. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.16 |
| bbChanGcra2Action GCRA2 Action.
1 = No Action
2 = Tag Untagged cells
3 = Tag untagged cells and discard tagged cells
4 = Discard all (0+1) non-comforming cells. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.17 |
| bbChanUpcSCRPolicing Selects SCR policing for CLP = 0 or all cells. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.18 |
| bbChanEfciThreshold Threshold above which EFCI bit is to be set.
Default Value is 3/4 of max cell count. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.19 |
| bbChanRowStatus This object is used for adding/deleting/modifying
entries in the table.
add(1) : Adds the entry.
delete(2) : Deletes the entry
modify(3) : Set this before mod… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.2 |
| bbChanDiscardOption Enable Frame Discard or CLP Hysteresis. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.20 |
| bbChanFrmDiscardThreshold Ingress Frame Discard Threshold.
Valid only when Ingress Frame Discard option is selected. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.21 |
| bbChanClpHiThreshold Ingress CLP High Threshold.
Default is 3/4 of max cell count. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.22 |
| bbChanClpLoThreshold Ingress CLP Low Threshold. Valid only when
Ingress CLP Hysteresis option is selected.
Default Value is 1/2 of max cell count. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.23 |
| bbChanCongstUpdateCode Ingress Channel Congestion Update Code. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.24 |
| bbChanMaxCellMemThreshold Maximum number of cells of that connection in
the memory.
Assuming Total Cell Memory is 512K cells, this is defaulted to
half of total size. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.25 |
| bbChanIngrPercentUtil Percentage Utilization of the IngrService Rate. This is used
for connection admission control. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.26 |
| bbChanEgrPercentUtil Percentage Utilization of the EgrService Rate.
This is used for egress bandwidth calculation and
connection admission control. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.27 |
| bbChanEgrSrvRate Egress service rate - This is used for egress bandwidth calculation
and for connection admission control. The actual value
depends on the speed of the logical interface. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.28 |
| bbChanOvrSubOvrRide Channel Over Subscrive Override
This MIB variable allows one to add a new connection on a port
even if it is over subscribed. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.29 |
| bbChanConnType This specifies the connection type
vpc(1) : Virtual Path Connection
vcc(2) : Virtual Channel Connection
This object can not be modified once the connection is creat… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.3 |
| bbChanLocalVpi The VPI value for this channel. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.30 |
| bbChanLocalVci The VCI value for this channel. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.31 |
| bbChanLocalNsapAddr The Near End NSAP Address value for this channel. | column | IfNsapAddress | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.32 |
| bbChanRemoteVpi The VPI value for this channel. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.33 |
| bbChanRemoteVci The VCI value for this channel. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.34 |
| bbChanRemoteNsapAddr The Far End NSAP Address value for this channel. | column | IfNsapAddress | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.35 |
| bbChanMaster This is used by the PXM switch platform module,
to determine if this endpoint ia master or slave. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.36 |
| bbChanRtePriority This is also known as class of service, it is used by
PXM to determine how important this connection is when
selecting connections to route. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.37 |
| bbChanMaxCost Maximum allowed cost. It is related to Cost Based Routing.
This is used by PXM so that it won't choose a path with a
cost greater than this configured level. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.38 |
| bbChanRestrictTrkType Restricted trunk type for routind, used by PXM.
It specifies that the connection either cannot be
routed over satellite trunks or terrestrial trunks,
or it can be on any type of… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.39 |
| bbChanServiceType This specifies the service type
cbr(1) : Constant Bit Rate
vbr(2) : Variable Bit Rate
abr(3) : Available Bit Rate
ubr(4) : Unspecified Bit Rate
vbr-rt(5): Variable Bit Rat… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.4 |
| bbChanTestType The chanTestType starts testing the continuity or delay
of a connection. It sends specific cell patterns toward
the network and the terminating end of this connection
has to be… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.40 |
| bbChanTestState This object provides the state of the test performed
on a connection.
When you add a connection then the chanTestState becomes notinprogress
and when you select any test, it woul… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.41 |
| bbChanTestResult This is round trip delay in milliseconds.
When you select testdelay option for the chanTestType,
the result of the test that is measured in milliseconds
can be read in chanTestRe… | column | milliseconds Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.42 |
| bbChanTestTypeCPESide The chanTestType starts testing the segment continuity
of a connection.
It sends OAM Segment loopback cell towards port side (CPE)
The CPE would loop back the cell
To test the co… | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.43 |
| bbConnVpcFlag This represents the connection type, used for PXM to
identify VPC/VCC. | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.45 |
| bbConnServiceType This specifies the service type
1 ==> Constant Bit Rate
2 ==> Variable Bit Rate
4 ==> Unspecified Bit Rate
6 ==> Available Bit Rate ( standard )
8 ==> Variable Bit Rate … | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.46 |
| bbConnPCR Peak cell rate, could be derived from the end point parameter | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.47 |
| bbConnSCR Sustained cell rate, could be derived from the end point parameter | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.48 |
| bbConnPercentUtil This is the expected long-term utilization of the
channel by this end-point. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.49 |
| bbChanConnDesc A string that has been defined to give a
descriptive name to the connection. | column | OctetString | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.5 |
| bbRemoteConnPCR Peak cell rate of the other end, if not set, will be
set to the same as local end PCR (bbChanUpcPCR). However,
note that if the PCRs for both local and remote end
are set to the d… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.50 |
| bbRemoteConnSCR Sustained cell rate of the other end, if not set, will be
set to the same as local end SCR (bbChanUpcSCR). However,
note that if the PCRs for both local and remote end
are set to … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.51 |
| bbRemoteConnPercentUtil This is the expected long-term utilization of the
channel by this end-point. If this is not specified in
the connection setup request, it'll be defaulted to
100 percent | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.52 |
| bbChanUpcMCR SCR, Sustainable Cell Rate, is an upper bound on the
conforming average rate of an ATM connection, over
time scales which are long relative to those for which
the PCR is defined. … | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.53 |
| bbChanSvcFlag This specifies the connection type
svc(1) : SVC connection
pvc(2) : PVC connection, used by PAR(Portable Auto Route)
spvc(3) : Soft PVC connection, used by PNNI | column | Enumeration | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.6 |
| bbChanSvcConnId This connection ID is for future use Currently not supported. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.7 |
| bbChanIfNum Channel's logical Interface from which traffic of the connection
will be received. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.8 |
| bbChanVpi VPI for the connection. | column | Integer32 | .1.3.6.1.4.1.351.110.5.2.7.1.1.1.9 |