portCrossIndex
CISCO-STACK-MIB ·
.1.3.6.1.4.1.9.5.1.4.1.1.3
Object
column
Integer32
A cross-reference to the port's index within another mib group. The value is dependent on the type of port. For an FDDI port, this corresponds to the snmpFddiPORTIndex.
Context
- MIB
- CISCO-STACK-MIB
- OID
.1.3.6.1.4.1.9.5.1.4.1.1.3- Type
- column
- Access
- readonly
- Status
- current
- Parent
- portEntry
- Table
- portTable
- Siblings
- 25
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-4080
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| portModuleIndex An index value that uniquely identifies the
module where this port is located. | column | Integer32 | .1.3.6.1.4.1.9.5.1.4.1.1.1 |
| portDuplex Indicates whether the port is operating in half-
duplex, full-duplex, disagree or auto negotiation
mode. If the port could not agree with the far end
on port duplex, the port will… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.10 |
| portIfIndex The value of the instance of the ifIndex object,
defined in MIB-II, for the interface corresponding
to this port. | column | Integer32 | .1.3.6.1.4.1.9.5.1.4.1.1.11 |
| portSpantreeFastStart deprecated Indicates whether the port is operating in
spantree fast start mode. A port with fast start
enabled is immediately put in spanning tree
forwarding state on link up, rather than st… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.12 |
| portAdminRxFlowControl Indicates the receive flow control administrative
status set on the port. If the status is set to
on(1), the port will require the far end to send
flow control. If the status is s… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.13 |
| portOperRxFlowControl Indicates the receive flow control operational
status of the port. If the port could not agree
with the far end on a link protocol, its
operational status will be disagree(3). | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.14 |
| portAdminTxFlowControl Indicates the transmit flow control
administrative status set on the port.
If the status is set to on(1), the port will send
flow control to the far end.
If the status is set to o… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.15 |
| portOperTxFlowControl Indicates the transmit flow control operational
status of the port. If the port could not agree
with the far end on a link protocol, its
operational status will be disagree(3). | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.16 |
| portMacControlTransmitFrames The total number of MAC control frames passed to
the MAC sublayer for transmission. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.5.1.4.1.1.17 |
| portMacControlReceiveFrames The total number of MAC control frames passed by
the MAC sublayer to the MAC Control sublayer on
receive. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.5.1.4.1.1.18 |
| portMacControlPauseTransmitFrames The total number of PAUSE frames passed to
the MAC sublayer for transmission. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.5.1.4.1.1.19 |
| portIndex An index value that uniquely identifies this port
within a module. The value is determined by the
location of the port on the module. Valid entries
are 1 to the value of moduleNum… | column | Integer32 | .1.3.6.1.4.1.9.5.1.4.1.1.2 |
| portMacControlPauseReceiveFrames The total number of PAUSE frames passed by
the MAC sublayer to the MAC Control sublayer
on receive. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.5.1.4.1.1.20 |
| portMacControlUnknownProtocolFrames The total number of MAC Control frames received
with an opcode that is not supported by the
device. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.5.1.4.1.1.21 |
| portLinkFaultStatus Specifies additional link fault status on a
gigabit link.
noFault:
Link is up and operational.
nearEndFault:
The port is enabled but there is no GBI… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.22 |
| portAdditionalOperStatus The current operational status of the port which
is showing additional detailed information of the
port. | column | Bits | .1.3.6.1.4.1.9.5.1.4.1.1.23 |
| portInlinePowerDetect Indicate if the port detects an inline power capable
device connected to it. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.5.1.4.1.1.24 |
| portEntPhysicalIndex The value of the instance of the entPhysicalIndex
object, defined in ENTITY-MIB, for the
entity physical index corresponding to this port. | column | ENTITY-MIBPhysicalIndex | .1.3.6.1.4.1.9.5.1.4.1.1.25 |
| portErrDisableTimeOutEnable Indicates whether a port that is put into
errdisable state by a cause as specified by
sysErrDisableTimeoutEnable will be re-enabled
automatically during the timeout interval as
sp… | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.26 |
| portName A descriptive string used by the network
administrator to name the port. | column | OctetString | .1.3.6.1.4.1.9.5.1.4.1.1.4 |
| portType The type of physical layer medium dependent
interface on the port. | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.5 |
| portOperStatus The current operational status of the port. | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.6 |
| portCrossGroupIndex A cross-reference to another mib group for this
port. The value is dependent on the type of port.
For an FDDI port this corresponds to the
snmpFddiPORTSMTIndex. | column | Integer32 | .1.3.6.1.4.1.9.5.1.4.1.1.7 |
| portAdditionalStatus Additional status information for the port. The
value is a sum. It initially takes the value zero,
then for each state that is true, 2 raised to a
power is added to the sum. The p… | column | Integer32 | .1.3.6.1.4.1.9.5.1.4.1.1.8 |
| portAdminSpeed The desired speed of the port.
The current operational speed of the port can be
determined from ifSpeed. | column | Enumeration | .1.3.6.1.4.1.9.5.1.4.1.1.9 |