portAdminSpeed

CISCO-STACK-MIB · .1.3.6.1.4.1.9.5.1.4.1.1.9
MIB view Table view

Object

column r/w Enumeration 
The desired speed of the port.
The current operational speed of the port can be
determined from ifSpeed.

Context

MIB
CISCO-STACK-MIB
OID
.1.3.6.1.4.1.9.5.1.4.1.1.9
Type
column
Access
readwrite
Status
current
Parent
portEntry
Table
portTable
Siblings
25

Syntax

Enumeration

Values & Constraints

Enumerated Values
1autoDetect
2autoDetect10100
10s10G
64000s64000
1544000s1544000
2000000s2000000
2048000s2048000
4000000s4000000
10000000s10000000
16000000s16000000
45000000s45000000
64000000s64000000
100000000s100000000
155000000s155000000
400000000s400000000
622000000s622000000
1000000000s1000000000

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
portModuleIndex
An index value that uniquely identifies the module where this port is located.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.1
portDuplex
Indicates whether the port is operating in half- duplex, full-duplex, disagree or auto negotiation mode. If the port could not agree with the far end on port duplex, the port will…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.10
portIfIndex
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.11
portSpantreeFastStart deprecated
Indicates whether the port is operating in spantree fast start mode. A port with fast start enabled is immediately put in spanning tree forwarding state on link up, rather than st…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.12
portAdminRxFlowControl
Indicates the receive flow control administrative status set on the port. If the status is set to on(1), the port will require the far end to send flow control. If the status is s…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.13
portOperRxFlowControl
Indicates the receive flow control operational status of the port. If the port could not agree with the far end on a link protocol, its operational status will be disagree(3).
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.14
portAdminTxFlowControl
Indicates the transmit flow control administrative status set on the port. If the status is set to on(1), the port will send flow control to the far end. If the status is set to o…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.15
portOperTxFlowControl
Indicates the transmit flow control operational status of the port. If the port could not agree with the far end on a link protocol, its operational status will be disagree(3).
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.16
portMacControlTransmitFrames
The total number of MAC control frames passed to the MAC sublayer for transmission.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.17
portMacControlReceiveFrames
The total number of MAC control frames passed by the MAC sublayer to the MAC Control sublayer on receive.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.18
portMacControlPauseTransmitFrames
The total number of PAUSE frames passed to the MAC sublayer for transmission.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.19
portIndex
An index value that uniquely identifies this port within a module. The value is determined by the location of the port on the module. Valid entries are 1 to the value of moduleNum…
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.2
portMacControlPauseReceiveFrames
The total number of PAUSE frames passed by the MAC sublayer to the MAC Control sublayer on receive.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.20
portMacControlUnknownProtocolFrames
The total number of MAC Control frames received with an opcode that is not supported by the device.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.21
portLinkFaultStatus
Specifies additional link fault status on a gigabit link. noFault: Link is up and operational. nearEndFault: The port is enabled but there is no GBI…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.22
portAdditionalOperStatus
The current operational status of the port which is showing additional detailed information of the port.
columnBits.1.3.6.1.4.1.9.5.1.4.1.1.23
portInlinePowerDetect
Indicate if the port detects an inline power capable device connected to it.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.5.1.4.1.1.24
portEntPhysicalIndex
The value of the instance of the entPhysicalIndex object, defined in ENTITY-MIB, for the entity physical index corresponding to this port.
columnENTITY-MIBPhysicalIndex.1.3.6.1.4.1.9.5.1.4.1.1.25
portErrDisableTimeOutEnable
Indicates whether a port that is put into errdisable state by a cause as specified by sysErrDisableTimeoutEnable will be re-enabled automatically during the timeout interval as sp…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.26
portCrossIndex
A cross-reference to the port's index within another mib group. The value is dependent on the type of port. For an FDDI port, this corresponds to the snmpFddiPORTIndex.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.3
portName
A descriptive string used by the network administrator to name the port.
columnOctetString.1.3.6.1.4.1.9.5.1.4.1.1.4
portType
The type of physical layer medium dependent interface on the port.
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.5
portOperStatus
The current operational status of the port.
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.6
portCrossGroupIndex
A cross-reference to another mib group for this port. The value is dependent on the type of port. For an FDDI port this corresponds to the snmpFddiPORTSMTIndex.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.7
portAdditionalStatus
Additional status information for the port. The value is a sum. It initially takes the value zero, then for each state that is true, 2 raised to a power is added to the sum. The p…
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.8