portAdditionalStatus

CISCO-STACK-MIB · .1.3.6.1.4.1.9.5.1.4.1.1.8
MIB view Table view

Object

column Integer32 
Additional status information for the port. The
value is a sum. It initially takes the value zero,
then for each state that is true, 2 raised to a
power is added to the sum. The powers are
according to the following table:
         State    Power
      Transmit    0
       Receive    1
     Collision    2
Transmit state indicates that at least one packet
was transmitted by the port in the last polling
period. Receive state indicates that at least one
packet was received by the port in the last
polling period. Collision state indicates that
at least one collision was detected on the port
in the last polling period.
Note that if a state is not applicable to a
particular port or additional status is not
supported on a particular port, its value is
always false for that port.

Context

MIB
CISCO-STACK-MIB
OID
.1.3.6.1.4.1.9.5.1.4.1.1.8
Type
column
Access
readonly
Status
current
Parent
portEntry
Table
portTable
Siblings
25

Syntax

Integer32

Values & Constraints

Object Constraints
range: 0-7

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
portModuleIndex
An index value that uniquely identifies the module where this port is located.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.1
portDuplex
Indicates whether the port is operating in half- duplex, full-duplex, disagree or auto negotiation mode. If the port could not agree with the far end on port duplex, the port will…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.10
portIfIndex
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.11
portSpantreeFastStart deprecated
Indicates whether the port is operating in spantree fast start mode. A port with fast start enabled is immediately put in spanning tree forwarding state on link up, rather than st…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.12
portAdminRxFlowControl
Indicates the receive flow control administrative status set on the port. If the status is set to on(1), the port will require the far end to send flow control. If the status is s…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.13
portOperRxFlowControl
Indicates the receive flow control operational status of the port. If the port could not agree with the far end on a link protocol, its operational status will be disagree(3).
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.14
portAdminTxFlowControl
Indicates the transmit flow control administrative status set on the port. If the status is set to on(1), the port will send flow control to the far end. If the status is set to o…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.15
portOperTxFlowControl
Indicates the transmit flow control operational status of the port. If the port could not agree with the far end on a link protocol, its operational status will be disagree(3).
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.16
portMacControlTransmitFrames
The total number of MAC control frames passed to the MAC sublayer for transmission.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.17
portMacControlReceiveFrames
The total number of MAC control frames passed by the MAC sublayer to the MAC Control sublayer on receive.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.18
portMacControlPauseTransmitFrames
The total number of PAUSE frames passed to the MAC sublayer for transmission.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.19
portIndex
An index value that uniquely identifies this port within a module. The value is determined by the location of the port on the module. Valid entries are 1 to the value of moduleNum…
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.2
portMacControlPauseReceiveFrames
The total number of PAUSE frames passed by the MAC sublayer to the MAC Control sublayer on receive.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.20
portMacControlUnknownProtocolFrames
The total number of MAC Control frames received with an opcode that is not supported by the device.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.5.1.4.1.1.21
portLinkFaultStatus
Specifies additional link fault status on a gigabit link. noFault: Link is up and operational. nearEndFault: The port is enabled but there is no GBI…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.22
portAdditionalOperStatus
The current operational status of the port which is showing additional detailed information of the port.
columnBits.1.3.6.1.4.1.9.5.1.4.1.1.23
portInlinePowerDetect
Indicate if the port detects an inline power capable device connected to it.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.5.1.4.1.1.24
portEntPhysicalIndex
The value of the instance of the entPhysicalIndex object, defined in ENTITY-MIB, for the entity physical index corresponding to this port.
columnENTITY-MIBPhysicalIndex.1.3.6.1.4.1.9.5.1.4.1.1.25
portErrDisableTimeOutEnable
Indicates whether a port that is put into errdisable state by a cause as specified by sysErrDisableTimeoutEnable will be re-enabled automatically during the timeout interval as sp…
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.26
portCrossIndex
A cross-reference to the port's index within another mib group. The value is dependent on the type of port. For an FDDI port, this corresponds to the snmpFddiPORTIndex.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.3
portName
A descriptive string used by the network administrator to name the port.
columnOctetString.1.3.6.1.4.1.9.5.1.4.1.1.4
portType
The type of physical layer medium dependent interface on the port.
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.5
portOperStatus
The current operational status of the port.
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.6
portCrossGroupIndex
A cross-reference to another mib group for this port. The value is dependent on the type of port. For an FDDI port this corresponds to the snmpFddiPORTSMTIndex.
columnInteger32.1.3.6.1.4.1.9.5.1.4.1.1.7
portAdminSpeed
The desired speed of the port. The current operational speed of the port can be determined from ifSpeed.
columnEnumeration.1.3.6.1.4.1.9.5.1.4.1.1.9