cSdslStucPsdMaskType
CISCO-SDSL-LINE-MIB ·
.1.3.6.1.4.1.9.9.155.1.14.1.8
Object
column
r/w
Enumeration
This object specifies the PSD mask type for the transceiver. For all values of the cSdslShdslLineMaxRate, the symmetric PSD masktype is selectable. Asymmetric mask is only selectable for the following rates: 776000, 784000, 1552000, 2056000, 2312000.
Context
- MIB
- CISCO-SDSL-LINE-MIB
- OID
.1.3.6.1.4.1.9.9.155.1.14.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cSdslLineConfProfileEntry
- Table
- cSdslLineConfProfileTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | symmetric |
2 | asymmetric |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cSdslLineMaxRate This object specifies the desired line rate which the STU-C
will attempt to train at. | column | bps Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.1 |
| cSdslLineEquipmentType This object specifies the type of the STU device ,either
STU-C or STU-R | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.10 |
| cSdslLineAutoRateEnable This object specifies whether the device uses the rate
adaptive training mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.155.1.14.1.11 |
| cSdslStucThresholdSnrMgn This object specifies the SNR margin threshold. An
appropriate alarm should be generated when the difference
between the actual SNR and the SNR required to maintain BER
of 10E… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.12 |
| cSdslSturAnnex This object specifies the operating conditions for the port
of G.shdsl CPE equipment. Annex A is optimized for conditions
typically encountered within the North American network… | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.13 |
| cSdslLineFramingMode This object specifies the desired Transmission Convergence
framing structure being used by the interface. | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.2 |
| cSdslStucTargetSnrMgn This object specifies the target SNR margin. This is the
desired noise margin the STU-C must achieve with a BER of
10-7 or better to successfully complete training. The value
f… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.3 |
| cSdslStucMaxSnrMgn This object specifies the maximum acceptable SNR margin.
If the noise margin exceeds this level, then the STU-C should
attempt to reduce its power output to optimize its operation… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.4 |
| cSdslStucMinSnrMgn This object specifies the minimum acceptable SNR margin.
If the noise margin falls below this level, the STU-C will
retrain. The value for this object must be in multiples of 10. … | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.5 |
| cSdslStucOutputPwr This object specifies the transmit power level used by
the STU-C. The value for this object must be in multiples
of 10. The specified value will be rounded down to the
nearest… | column | tenth dBm Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.6 |
| cSdslShdslLineMaxRate This object specifies the desired line rate at which the
G.shdsl STU-C will attempt to train. | column | bps Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.7 |
| cSdslStucAnnex This object specifies the operating conditions for the port
of G.shdsl CO equipment . Annex A is optimized for conditions
typically encountered within the North American network… | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.9 |