cSdslLineMaxRate
CISCO-SDSL-LINE-MIB ·
.1.3.6.1.4.1.9.9.155.1.14.1.1
Object
column
r/w
bps Integer32
This object specifies the desired line rate which the STU-C will attempt to train at.
Context
- MIB
- CISCO-SDSL-LINE-MIB
- OID
.1.3.6.1.4.1.9.9.155.1.14.1.1- Type
- column
- Access
- readwrite
- Status
- current
- Units
- bps
- Parent
- cSdslLineConfProfileEntry
- Table
- cSdslLineConfProfileTable
- Siblings
- 12
Syntax
bps Integer32
Values & Constraints
Object Constraints
range: 144000-144000
range: 272000-272000
range: 400000-400000
range: 528000-528000
range: 784000-784000
range: 1040000-1040000
range: 1168000-1168000
range: 1552000-1552000
range: 2064000-2064000
range: 2320000-2320000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cSdslLineEquipmentType This object specifies the type of the STU device ,either
STU-C or STU-R | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.10 |
| cSdslLineAutoRateEnable This object specifies whether the device uses the rate
adaptive training mode. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.155.1.14.1.11 |
| cSdslStucThresholdSnrMgn This object specifies the SNR margin threshold. An
appropriate alarm should be generated when the difference
between the actual SNR and the SNR required to maintain BER
of 10E… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.12 |
| cSdslSturAnnex This object specifies the operating conditions for the port
of G.shdsl CPE equipment. Annex A is optimized for conditions
typically encountered within the North American network… | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.13 |
| cSdslLineFramingMode This object specifies the desired Transmission Convergence
framing structure being used by the interface. | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.2 |
| cSdslStucTargetSnrMgn This object specifies the target SNR margin. This is the
desired noise margin the STU-C must achieve with a BER of
10-7 or better to successfully complete training. The value
f… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.3 |
| cSdslStucMaxSnrMgn This object specifies the maximum acceptable SNR margin.
If the noise margin exceeds this level, then the STU-C should
attempt to reduce its power output to optimize its operation… | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.4 |
| cSdslStucMinSnrMgn This object specifies the minimum acceptable SNR margin.
If the noise margin falls below this level, the STU-C will
retrain. The value for this object must be in multiples of 10. … | column | tenth dB Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.5 |
| cSdslStucOutputPwr This object specifies the transmit power level used by
the STU-C. The value for this object must be in multiples
of 10. The specified value will be rounded down to the
nearest… | column | tenth dBm Integer32 | .1.3.6.1.4.1.9.9.155.1.14.1.6 |
| cSdslShdslLineMaxRate This object specifies the desired line rate at which the
G.shdsl STU-C will attempt to train. | column | bps Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.7 |
| cSdslStucPsdMaskType This object specifies the PSD mask type for the transceiver.
For all values of the cSdslShdslLineMaxRate, the symmetric PSD
masktype is selectable. Asymmetric mask is only selec… | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.8 |
| cSdslStucAnnex This object specifies the operating conditions for the port
of G.shdsl CO equipment . Annex A is optimized for conditions
typically encountered within the North American network… | column | Enumeration | .1.3.6.1.4.1.9.9.155.1.14.1.9 |