clMeshNodeBHDataRate

CISCO-LWAPP-MESH-MIB · .1.3.6.1.4.1.9.9.616.1.1.1.1.15
MIB view Table view

Object

column r/w Enumeration 
This object specifies the rate at which packets are sent
on the backhaul link. Depending on the backhaul radio type,
denoted by clMeshNodeBackhaul object, data rate will vary.
              
If the value of clMeshNodeBackhaul object is 'dot11a', 
data rates can be one of the following 
possible values.
mbps6(4)
mbps9(5)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)
              
Additionally following data rates are supported if 802.11a
supports 11n.
htMcs0(14)
htMcs1(15)
htMcs2(16)
htMcs3(17)
htMcs4(18)
htMcs5(19)
htMcs6(20)
htMcs7(21)
htMcs8(22)
htMcs9(23)
htMcs10(24)
htMcs11(25)
htMcs12(26)
htMcs13(27)
htMcs14(28)
htMcs15(29)
              
If the value of clMeshNodeBackhaul object is 'dot11b', 
then data rate can be one of the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps11(6)
auto(13)
              
If the value of clMeshNodeBackhaul object is 'dot11g', 
then data rate can be one of the following possible values.
mbps1(1)
mbps2(2)
mbps5point5(3)
mbps6(4)
mbps9(5)
mbps11(6)
mbps12(7)
mbps18(8)
mbps24(9)
mbps36(10)
mbps48(11)
mbps54(12)
auto(13)

Context

MIB
CISCO-LWAPP-MESH-MIB
OID
.1.3.6.1.4.1.9.9.616.1.1.1.1.15
Type
column
Access
readwrite
Status
current
Parent
clMeshNodeEntry
Table
clMeshNodeTable
Siblings
27

Syntax

Enumeration

Values & Constraints

Enumerated Values
1mbps1
2mbps2
3mbps5point5
4mbps6
5mbps9
6mbps11
7mbps12
8mbps18
9mbps24
10mbps36
11mbps48
12mbps54
13auto
14htMcs0
15htMcs1
16htMcs2
17htMcs3
18htMcs4
19htMcs5
20htMcs6
21htMcs7
22htMcs8
23htMcs9
24htMcs10
25htMcs11
26htMcs12
27htMcs13
28htMcs14
29htMcs15
30htMcs16
31htMcs17
32htMcs18
33htMcs19
34htMcs20
35htMcs21
36htMcs22
37htMcs23
38vhtMcs0Ss1
39vhtMcs1Ss1
40vhtMcs2Ss1
41vhtMcs3Ss1
42vhtMcs4Ss1
43vhtMcs5Ss1
44vhtMcs6Ss1
45vhtMcs7Ss1
46vhtMcs8Ss1
47vhtMcs9Ss1
48vhtMcs0Ss2
49vhtMcs1Ss2
50vhtMcs2Ss2
51vhtMcs3Ss2
52vhtMcs4Ss2
53vhtMcs5Ss2
54vhtMcs6Ss2
55vhtMcs7Ss2
56vhtMcs8Ss2
57vhtMcs9Ss2
58vhtMcs0Ss3
59vhtMcs1Ss3
60vhtMcs2Ss3
61vhtMcs3Ss3
62vhtMcs4Ss3
63vhtMcs5Ss3
64vhtMcs6Ss3
65vhtMcs7Ss3
66vhtMcs8Ss3
67vhtMcs9Ss3
65535default

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
clMeshNodeRole
This object specifies the role of mesh AP which has joined the controller. See glossary section above for detail about MAP and RAP. map - AP is configured as mesh. rap - AP is co…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.1
clMeshNodeInternalTemp
This object represents the internal temperature of mesh node in celsius.
columndegree Celsius SNMPv2-SMIInteger32.1.3.6.1.4.1.9.9.616.1.1.1.1.10
clMeshNodeType
This object represents the type of mesh node. indoor - Mesh node which is manufactured to be used inside the building. outdoor - Mesh node which can be used outside b…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.11
clMeshNodeHops
This object represents the number of hops a MAP mesh node is from RAP. When the clMeshNodeRole is set to 'RAP' this object will return a value of zero.
columnhops SNMPv2-SMIGauge32.1.3.6.1.4.1.9.9.616.1.1.1.1.12
clMeshNodeChildCount
This object represents the number of children MAPs of a RAP or a MAP.
columnSNMPv2-SMIGauge32.1.3.6.1.4.1.9.9.616.1.1.1.1.13
clMeshNodeBackhaulRadio
This object specifies the type of radio used for backhaul access. unknown (1) unsupported APs dot11bg (2) The value dot11b sets the 802.11b radio as backhaul radi…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.14
clMeshDaisyChainEnabled
This object specifies whether an AP operating in mesh mode has daisy chaining mode enabled. A daisy chain is a wiring scheme in which multiple devices are wired together in sequ…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.16
clMeshPrefParentMacAddress
This object represents the MAC address of the preferred parent for this mesh node.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.9.9.616.1.1.1.1.17
clMeshNodeBGNStrictMatch
This object specifies whether an AP operating in mesh mode needs to have needs to have strict bridge group matching enabled or not. A value of 'true' indicates that strict bridge…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.18
clMeshNodeVlanEnabled
This object specifies whether an AP operating in mesh mode has VLAN support enabled. If flexconnect local switching is enabled, it will return the same value as cLReapApVlanEnable…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.19
clMeshNodeGroupName
This object specifies the group name of the mesh sector. MAP AP will join the mesh sector which has the same group name configured on RAP AP.
columnOctetString.1.3.6.1.4.1.9.9.616.1.1.1.1.2
clMeshNodeNativeVlanId
This object specifies the native VLAN ID configured on the AP. If flexconnect local switching is enabled, it will return the same value as cLReapApNativeVlanId.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.616.1.1.1.1.20
clMeshNodePskKeyClear
This object specifies clearing of PSK key. A value of 'true' indicates PSK key will be cleared. A value of 'false' indicates PSK key wont be cleared.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.21
clMeshNodeRAPDownlinkBackhaul
This objects specifies the current backhaul slot of the RAP. And also used to configure/change the backhaul slot of the RAP. slot0 - downlink backhaul access for slot 0 enabled. s…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.22
clMeshNodeBlockChild
This object specifies Block Child state for the AP. A value of 'true' indicates block child state is enabled. A value of 'false' indicates block child state is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.23
clMeshNodeBhaulDataRateType
This object specifies the backhaul tx data rate type for Mesh AP. And also used to configure/change the mesh backhaul data rate for AP. auto - Backhaul tx rate is automatically se…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.24
clMeshNodeBhaulDataRate
This object specifies the backhaul tx rate in kbps Backhaul tx rate is one of 1000, 2000, 5500, 11000, 6000, 9000, 12000, 18000, 24000, 36000, 48000, 54000
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.25
clMeshNodeBhaulDataRateMcsIndex
This object specifies the backhaul tx rate 802.11n/ac mcs index Backhaul mcs index is between 0 to 31 for 802.11n and 0 to 9 for 802.11ac.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.616.1.1.1.1.26
clMeshNodeBhaulDataRateDot11acSpatialStream
This object specifies the backhaul rate 802.11ac spatial stream value of backhaul rate spatial stream is between 1 to 4.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.616.1.1.1.1.27
clMeshNodeBhaulDataRateDot11axSpatialStream
This object specifies the backhaul rate 802.11ax spatial stream value. Range of 1 - 4 for 802.11bg and 1 - 8 for 802.11 radio.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.616.1.1.1.1.28
clMeshNodeBackhaul
This object represents 802.11 interface type of the backhaul link. See Mesh Link in glossary section for more detail on backhaul link. dot11a - 802.11a radio is used as backha…
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.3
clMeshNodeBackhaulDataRate deprecated
This object represents the rate at which packets are sent on the backhaul link. This object has been deprecated for clMeshNodeBHDataRate.
columnKbps SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.616.1.1.1.1.4
clMeshNodeEthernetBridge
This object specifies whether ethernet bridge is enabled or not. A value of 'true' indicates ethernet bridging is enable on this mesh node. A value of 'false indicates ethernet b…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.5
clMeshNodeEthernetLinkStatus
This object represents whetherthe link is up or down on the ethernet port of the RAP or MAP. up - ethernet link is up. down - ethernet link is down.
columnEnumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.6
clMeshNodePublicSafetyBackhaul deprecated
4.9Ghz considered to be public safety band and is limited to some service providers. A value of true indicates that 4.9 Ghz can be used on backhaul link by selecting channel on t…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.616.1.1.1.1.7
clMeshNodeParentMacAddress
This object represents the MAC address of a parent mesh node. In case of RAP this object will return 0000000000000.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.9.9.616.1.1.1.1.8
clMeshNodeHeaterStatus
This object represents the heater status of the mesh node. on - heater is in operation off - heater is not operation.
columnPercent Enumeration.1.3.6.1.4.1.9.9.616.1.1.1.1.9