cHsrpGrpConfiguredHoldTime
CISCO-HSRP-MIB ·
.1.3.6.1.4.1.9.9.106.1.2.1.1.8
Object
If cHsrpGrpUseConfiguredTimers is true, cHsrpGrpConfiguredHoldTime is used when this router is an active router. Otherwise, the Holdtime learned from the current active router is used. All routers on a particular LAN segment should use the same Holdtime. Also, the Holdtime should be at least three times the value of the Hellotime and must be greater than the Hellotime.
Context
- MIB
- CISCO-HSRP-MIB
- OID
.1.3.6.1.4.1.9.9.106.1.2.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- cHsrpGrpEntry
- Table
- cHsrpGrpTable
- Siblings
- 17
Syntax
milliseconds SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cHsrpGrpNumber This object along with the ifIndex of a particular interface
uniquely identifies an HSRP group.
Group numbers 0,1 and 2 are the only valid group numbers
for TokenRi… | column | Unsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.1 |
| cHsrpGrpLearnedHoldTime If the Holdtime is not configured on a router, it can be
learned from the Hello message from the active router.
Holdtime should be learned only if the Hello message is
authenticat… | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.10 |
| cHsrpGrpVirtualIpAddr This is the primary virtual IP address used by this
group. If this address is configured (i.e a non zero ip
address), this value is used. Otherwise, the agent will
attempt to dis… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.106.1.2.1.1.11 |
| cHsrpGrpUseConfigVirtualIpAddr If this object is TRUE, cHsrpGrpVirtualIpAddr was a
configured one. Otherwise, it indicates that
cHsrpGrpVirtualIpAddr was a learned one. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.106.1.2.1.1.12 |
| cHsrpGrpActiveRouter Ip Address of the currently active router for this group. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.106.1.2.1.1.13 |
| cHsrpGrpStandbyRouter Ip Address of the currently standby router for this
group. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.106.1.2.1.1.14 |
| cHsrpGrpStandbyState The current HSRP state of this group on this interface. | column | HsrpState | .1.3.6.1.4.1.9.9.106.1.2.1.1.15 |
| cHsrpGrpVirtualMacAddr Mac Addresses used are as specified in RFC 2281. For
ethernet and fddi interfaces, a MAC address will be in the
range 00:00:0c:07:ac:00 through 00:00:0c:07:ac:ff. The last
octet i… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.106.1.2.1.1.16 |
| cHsrpGrpEntryRowStatus The control that allows modification, creation, and
deletion of entries. For detailed rules see the
DESCRIPTION for cHsrpGrpEntry. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.106.1.2.1.1.17 |
| cHsrpGrpIpNone This object specifies the disable HSRP IPv4 virtual
IP address. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.106.1.2.1.1.18 |
| cHsrpGrpAuth This is an unencrypted authentication string which is
carried in all HSRP messages. An authentication string
mismatch prevents a router interface from learning the
designated IP a… | column | OctetString | .1.3.6.1.4.1.9.9.106.1.2.1.1.2 |
| cHsrpGrpPriority The cHsrpGrpPriority helps to select the active and the
standby routers. The router with the highest priority is
selected as the active router. In the priority range of 0
to 255, … | column | Unsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.3 |
| cHsrpGrpPreempt This object, if TRUE, indicates that the current router
should attempt to overthrow a lower priority active router
and attempt to become the active router. If this object is
FALSE… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.106.1.2.1.1.4 |
| cHsrpGrpPreemptDelay This delay is the time difference between a router power
up and the time it can actually start preempting the
currently active router.
When a router first comes up,… | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.5 |
| cHsrpGrpUseConfiguredTimers HSRP routers learn a group's Hellotime or Holdtime from
hello messages.
The Hellotime is used to determine the frequency of
generating hello messages when this rout… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.106.1.2.1.1.6 |
| cHsrpGrpConfiguredHelloTime If cHsrpGrpUseConfiguredTimers is true,
cHsrpGrpConfiguredHelloTime is used when this router is an
active router. Otherwise, the Hellotime learned from the
current active router i… | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.7 |
| cHsrpGrpLearnedHelloTime If the Hellotime is not configured on a router, it can be
learned from the Hello messages from active router,
provided the Hello message is authenticated. If the
Hellotime is not … | column | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.106.1.2.1.1.9 |