cdspDtmfPowerTwist
CISCO-DSP-MGMT-MIB ·
.1.3.6.1.4.1.9.9.86.1.4.1.1.7
Object
column
r/w
0.1 dB Integer32
This object specifies the relative power level of the high frequency component of DTMF. The low frequency group is always fixed to the value specified by cdspDtmfPowerLevel. When this object is set to 0, the power level of both frequency components is set to the same level. When this object is set to a positive value, the power level of the high frequency component is set to relatively higher specified in this object than the low frequency component. For example if cdspDtmfPowerLevel is set to -120(-12 dBm) and this object is set to 50, the power level of the high frequency component becomes -70(-7 dBm). When this object is set to a negative value, the power level of the high frequency component is set to relatively lower specified in this object than the low frequency component. For example if cdspDtmfPowerLevel is set to -120(-12 dBm) and this object is set to -100, the power level of the high frequency component becomes -220(-22 dBm). The power level of the high frequency component has to be in the data range specified in cdspDtmfPowerLevel. For example if cdspDtmfPowerLevel is set to -200(-20 dBm) and this object is set to -100, the power level of the high frequency component will become -300(-30 dBm) which is out of the range (-250..30) of data specified in cdspDtmfPowerLevel, so -100 is illegitimate for this setting.
Context
- MIB
- CISCO-DSP-MGMT-MIB
- OID
.1.3.6.1.4.1.9.9.86.1.4.1.1.7- Type
- column
- Access
- readwrite
- Status
- current
- Units
- 0.1 dB
- Parent
- cdspVoiceParamEntry
- Table
- cdspVoiceParamTable
- Siblings
- 16
Syntax
0.1 dB Integer32
Values & Constraints
Object Constraints
range: -100-100
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cdspRtpSidPayloadType This object specifies the RTP (Real Time Protocol) payload
type of the SID (Silence Insertion Descriptor) packet
that is sent to the remote endpoint at the onset
of silence supp… | column | Enumeration | .1.3.6.1.4.1.9.9.86.1.4.1.1.1 |
| cdspRtcpXrControl This object controls if RTCPXR
(Real Time Control Protocol Extended Report) is enabled.
If this object is set to 'true', both transmission and
reception of RTCPXR packets are ena… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.86.1.4.1.1.10 |
| cdspRtcpXrTransMultiplier This object is used to configure the RTCPXR report
frequency. i.e. how many RTCP packets during the interval
of every RTCPXR packet.
The RTCPXR report is sent every 'cdspRtcpXrTra… | column | Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.11 |
| cdspRtcpXrGminDefault This object is the default minimum gap value configured
for the IP stream.
This object is applicable only if 'cdspVqmControl' is
set to 'rfc3611Vqm'. | column | Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.12 |
| cdspRtcpXrExtRfactor This object is the external R factor metric value.
The value 127 means it is not applicable.
This object is applicable only if 'cdspVqmControl' is
set to 'rfc3611Vq… | column | Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.13 |
| cdspPktLossConcealment This object specifies the packet loss concealment:
(1) none: No packet loss concealment applied
(2) simple: Cisco Proprietary packet loss concealment
(3) g711A1: IT… | column | Enumeration | .1.3.6.1.4.1.9.9.86.1.4.1.1.14 |
| cdspVqmThreshSES This attribute specifies the threshold for
Severely Errored Second on VQM. If the total
number of milliseconds sampled as bad voice quality
in one second period exceeds threshol… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.15 |
| cdspTransparentIpIp deprecated This attribute is used to enable or disable the transparent
mode when establishing a non-transcoding IP-IP connection.
The attribute does not apply for the transcoding IP-IP
conne… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.86.1.4.1.1.16 |
| cdspVoiceModeIpIp This object specifies the voice mode for IP IP connections.
normal : A normal Mode is a transcoding mode for IP-IP
connections where the bearer properties will
… | column | Enumeration | .1.3.6.1.4.1.9.9.86.1.4.1.1.17 |
| cdspRtcpControl This objects controls if RTCP (Real Time Control Protocol)
will be enabled.
If this object is set to 'true', both transmission and
reception of RTCP packets are enabled; otherwis… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.86.1.4.1.1.2 |
| cdspRtcpTransInterval This attribute specifies the RTCP report interval (defined
in RFC1889). It indicates the interval in which the RTCP
reports should be sent to the participating members.
… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.3 |
| cdspRtcpRecvMultiplier This object specifies an approximate RTCP report interval
(defined in RFC 1889) in milliseconds in which the RTCP
reports should be sent to the participating members.
… | column | Unsigned32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.4 |
| cdspVadAdaptive This attribute is used to enable or disable the Adaptive
VAD knob of the VAD algorithm.
Adaptive VAD works in conjunction with VAD Threshold
(cvifcfgMusicOnHoldThreshold from CIS… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.86.1.4.1.1.5 |
| cdspDtmfPowerLevel This object specifies the power level of the low
frequency component of DTMF. The power level of the high
frequency component of DTMF is relative above or below
the value specifi… | column | 0.1 dBm Integer32 | .1.3.6.1.4.1.9.9.86.1.4.1.1.6 |
| cdspRtcpTimerControl This object specifies when the RTCP receive timer
is started.
disabled - timer is disabled
startImmediately - timer starts immediately
… | column | Enumeration | .1.3.6.1.4.1.9.9.86.1.4.1.1.8 |
| cdspVqmControl This object is used to disable VQM or enable either
RFC 3611 RTCPXR or Extended Network Quality Metrics VQM.
disable - VQM is disabled.
rfc3611Vqm - RFC 3611 RTCPX… | column | Enumeration | .1.3.6.1.4.1.9.9.86.1.4.1.1.9 |