cds3LineType

CISCO-DS3-MIB · .1.3.6.1.4.1.9.9.132.1.1.1.1.1

Object

column r/w Enumeration

This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps.
              
The values, in sequence, describe:
              
 Following values are applicable to DS3 interfaces only.
              
  ds3cbitadm       : Indicates C-BIT ADM mode 
  ds3cbitplcp      : Indicates C-BIT PLCP mode
  ds3m23adm        : Indicates M23 ADM mode 
  ds3m23plcp       : Indicates M23 PLCP mode 
  dsx3M23          : Refer ANSI T1.107-1988 [9]
  dsx3SYNTRAN      : Refer ANSI T1.107-1988 [9]
  dsx3CbitParity   : Refer ANSI T1.107-1988 [9]
  dsx3ClearChannel : Refer ANSI T1.107-1988 [9]
  ds3cbitfrmronly  : Indicates C-BIT FRAMER-ONLY mode
  ds3m23frmronly   : Indicates M23 FRAMER-ONLY mode
              
 Following values are applicable to E3 interfaces only.
              
  e3g832adm      : Indicates G.832 ADM mode 
  e3g751adm      : Indicates G.751 ADM mode 
  e3g751plcp     : Indicates G.751 PLCP mode
  e3Framed       : Refer CCITT G.751 [12]
  e3Plcp         : Refer ETSI T/NA(91)19 [14]
  e3g832frmronly : Indicates G.832 FRAMER-ONLY mode
  e3g751frmronly : Indicates G.751 FRAMER-ONLY mode.

Context

MIB: CISCO-DS3-MIB
OID: .1.3.6.1.4.1.9.9.132.1.1.1.1.1
Type: column
Access: readwrite
Status: current
Parent: cds3ConfigEntry
Table: cds3ConfigTable
Siblings: 9

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	ds3cbitadm
`2`	ds3cbitplcp
`3`	e3g832adm
`4`	e3g751adm
`5`	e3g751plcp
`6`	ds3m23adm
`7`	ds3m23plcp
`8`	other
`9`	dsx3M23
`10`	dsx3SYNTRAN
`11`	dsx3CbitParity
`12`	dsx3ClearChannel
`13`	e3Framed
`14`	e3Plcp
`15`	ds3cbitfrmronly
`16`	ds3m23frmronly
`17`	e3g832frmronly
`18`	e3g751frmronly

Related Objects

Sibling Objects

Object	Type	Syntax	OID
cds3FarEndLineLoopbackStatus Indicates the loopback status of the far end DS3,DS1 when remote DS1 loopback request is initiated. The remote DS1 loopback is initiated by setting dsx3SendCode object to dsx3Sen…	column	Unsigned32	`.1.3.6.1.4.1.9.9.132.1.1.1.1.10`
cds3LineAIScBitsCheck When check(1) is set, then Alarm Indication Signal (AIS) is declared when '1010...'b is found and C-Bits are all zero. When ignore(2) is set, an AIS condition is declared when …	column	Enumeration	`.1.3.6.1.4.1.9.9.132.1.1.1.1.2`
cds3LineRcvFEACValidation This entry specifies the FEAC (Far End Alarm and Control) code validation criteria. If 'fEACCodes4Of5' is specified, then a valid FEAC code is declared if 4 of 5 codes match. Whe…	column	Enumeration	`.1.3.6.1.4.1.9.9.132.1.1.1.1.3`
cds3LineOOFCriteria This entry specifies the out of frame(OOF) decision criteria. If 'bits3Of8' is specified then an OOF condition is declared if at least 3 of 8 framing bits are in error. When 'bits…	column	Enumeration	`.1.3.6.1.4.1.9.9.132.1.1.1.1.4`
cds3TraceToTransmit Transmitted G.832 Trail Trace string.	column	OctetString	`.1.3.6.1.4.1.9.9.132.1.1.1.1.5`
cds3TraceToExpect G.832 Trail Trace string that is expected to be received from the other end.	column	OctetString	`.1.3.6.1.4.1.9.9.132.1.1.1.1.6`
cds3TraceAlarm The value of this object is set to traceFailure(2) when DS3 line receives a trace does not match the 'cds3TraceToExpect'.	column	Enumeration	`.1.3.6.1.4.1.9.9.132.1.1.1.1.7`
cds3InternalEqualizer This variable indicates whether the internal equalizer is being used or bypassed. Set this value depending on the line equipment to which the receiver is attached. Possible values…	column	Enumeration	`.1.3.6.1.4.1.9.9.132.1.1.1.1.8`
cds3NearEndLineLoopbackStatus Indicates the loopback status of the near end DS1 on this DS3 when loopback request is indicated. Following table lists the mapping of Bit position to DS1 or DS3 l…	column	Unsigned32	`.1.3.6.1.4.1.9.9.132.1.1.1.1.9`