cds3LineOOFCriteria
CISCO-DS3-MIB ·
.1.3.6.1.4.1.9.9.132.1.1.1.1.4
Object
column
r/w
Enumeration
This entry specifies the out of frame(OOF) decision criteria. If 'bits3Of8' is specified then an OOF condition is declared if at least 3 of 8 framing bits are in error. When 'bits3Of16' is specified then OOF is declared if 3 of 16 framing bits are found to be in error. OOF is declared when errors are detected in the framing octets for four consecutive frames. This object does not apply to E3 interface. The value notApplicable(3) is used in case of the interfaces where this object is not applicable. The notApplicable(3) is not allowed in write operation.
Context
- MIB
- CISCO-DS3-MIB
- OID
.1.3.6.1.4.1.9.9.132.1.1.1.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cds3ConfigEntry
- Table
- cds3ConfigTable
- Siblings
- 9
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | bits3Of8 |
2 | bits3Of16 |
3 | notApplicable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cds3LineType This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics.… | column | Enumeration | .1.3.6.1.4.1.9.9.132.1.1.1.1.1 |
| cds3FarEndLineLoopbackStatus Indicates the loopback status of the far end DS3,DS1
when remote DS1 loopback request is initiated.
The remote DS1 loopback is initiated by setting dsx3SendCode
object to dsx3Sen… | column | Unsigned32 | .1.3.6.1.4.1.9.9.132.1.1.1.1.10 |
| cds3LineAIScBitsCheck When check(1) is set, then Alarm Indication Signal (AIS)
is declared when '1010...'b is found and C-Bits are all zero.
When ignore(2) is set, an AIS condition is declared when … | column | Enumeration | .1.3.6.1.4.1.9.9.132.1.1.1.1.2 |
| cds3LineRcvFEACValidation This entry specifies the FEAC (Far End Alarm and Control) code
validation criteria. If 'fEACCodes4Of5' is specified, then a valid
FEAC code is declared if 4 of 5 codes match. Whe… | column | Enumeration | .1.3.6.1.4.1.9.9.132.1.1.1.1.3 |
| cds3TraceToTransmit Transmitted G.832 Trail Trace string. | column | OctetString | .1.3.6.1.4.1.9.9.132.1.1.1.1.5 |
| cds3TraceToExpect G.832 Trail Trace string that is expected to be received from
the other end. | column | OctetString | .1.3.6.1.4.1.9.9.132.1.1.1.1.6 |
| cds3TraceAlarm The value of this object is set to traceFailure(2) when
DS3 line receives a trace does not match the
'cds3TraceToExpect'. | column | Enumeration | .1.3.6.1.4.1.9.9.132.1.1.1.1.7 |
| cds3InternalEqualizer This variable indicates whether the internal equalizer is being
used or bypassed. Set this value depending on the line equipment
to which the receiver is attached.
Possible values… | column | Enumeration | .1.3.6.1.4.1.9.9.132.1.1.1.1.8 |
| cds3NearEndLineLoopbackStatus Indicates the loopback status of the near end DS1 on this
DS3 when loopback request is indicated.
Following table lists the mapping of Bit position to
DS1 or DS3 l… | column | Unsigned32 | .1.3.6.1.4.1.9.9.132.1.1.1.1.9 |