ccasLSTIdleGuardTimer
CISCO-CAS-IF-EXT-MIB ·
.1.3.6.1.4.1.9.9.314.1.3.3.1.2
Object
column
r/w
milliseconds Unsigned32
This object specifies the maximum amount of time MG will wait for receipt of the idle signal on the line. For T1 interfaces idle signal corresponds to on-hook pattern on line. For E1 interfaces idle signal corresponds to idle pattern on line. The value of 0 indicates the timer will not be started and MG would wait forever.
Context
- MIB
- CISCO-CAS-IF-EXT-MIB
- OID
.1.3.6.1.4.1.9.9.314.1.3.3.1.2- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- ccasIfExtLineSignalTimerEntry
- Table
- ccasIfExtLineSignalTimerTable
- Siblings
- 11
Syntax
milliseconds Unsigned32
Values & Constraints
Object Constraints
range: 0-4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ccasLSTIndex An arbitrary index that uniquely identifies a
entry in the ccasIfExtLineSignalTimerTable.
The index 1 is reserved for the default entry. | column | Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.1 |
| ccasLSTDelayBetRegAnsAndLineAns This object specifies the timer that will be started
after register signaling completes successfully,
within which the answer line signal should be
received.
This applies to o… | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.10 |
| ccasLSTSeizeAckToDigitTimer This object specifies the amount of time that the GW
should wait for the reception address digits after
sending seize ack signal.
The value of 0 indicates the timer will not be… | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.11 |
| ccasLSTRowStatus This object is used for adding, deleting, and modifying
the entries from the ccasIfExtLineSignalTimerTable.
A default entry with index value 1 is created at
initialization, and… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.314.1.3.3.1.12 |
| ccasLSTClearFwdTimer This object specifies the value of the timer that the GW
will start at the request of the controlling application
such as MGC for receipt of the clear forward signal on the
lin… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.3 |
| ccasLSTClearBwdTimer This object specifies the value of the timer that the GW
will start at the request of the controlling application
such as MGC for receipt of the clear backward signal.
This obj… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.4 |
| ccasLSTReleaseGuardTimer This object specifies the delay between reception of the
clear forward signal and the sending of the idle signal.
Upon reception of the clear forward signal, GW starts the
rel… | column | millliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.5 |
| ccasLSTCASGlareTimer This object specifies the maximum amount of time MG will
wait for other end to back out when glare occurs on a DS0
line.
Change in incoming off-hook signal to on-hook signal
… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.6 |
| ccasLSTAnswerMeterDelayTimer The object specifies the delay between generation of the
answer signal and the generation of the meter signal.
The GW will start this timer after having sent the line
answer sig… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.7 |
| ccasLSTCASDebounceTimer This object specifies the amount of time for which the line
signal should persist to be valid.
The value of ccasLSTCASDebounceTimer must be less than or
equal the value of foll… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.8 |
| ccasLSTSeizeAckRspTimer This object specifies the maximum amount of time MG will
wait for reception of seize ack signal.
Seize Ack signal is expected in response of seize signal.
This object is applied … | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.3.3.1.9 |