ccasGCnfGlarePolicy
CISCO-CAS-IF-EXT-MIB ·
.1.3.6.1.4.1.9.9.314.1.6.1.1.2
Object
column
r/w
Enumeration
This object specifies a glare policy. It is used only if CAS DS0 directionality of the endpoint is bidirectional, and is applicable for non R2 variants. . rptSzOnGlareTmrExp (1): When glare is detected, the GW will wait for the timeout value specified in the glare timer object or until incoming call attempt is removed by the other exchange/switch. If the far end does not back off due to wrong configuration, and the GW times out, it reports the seize event to the controlling application. . rptSzOnGlareDet (2): When glare is detected, the GW will signal the seizure event to the controlling application. . rptRelOnGlareTmrExpAndGoOnHook (3): When glare is detected, the GW will wait for the timeout value specified in the glare timer object OR until incoming call attempt is removed by the other exchange/switch. If the far end does not back off, due to wrong configuration, and the GW times out, it reports the release event and goes onhook, upon detection of on hook from the far end the GW will send the rlc event to the controlling application. . goOnHookOnGlareDet (4): When glare is detected, the GW will go on hook and let the far end switch continue.
Context
- MIB
- CISCO-CAS-IF-EXT-MIB
- OID
.1.3.6.1.4.1.9.9.314.1.6.1.1.2- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ccasIfExtGeneralConfigEntry
- Table
- ccasIfExtGeneralConfigTable
- Siblings
- 33
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | rptSzOnGlareTmrExp |
2 | rptSzOnGlareDet |
3 | rptRelOnGlareTmrExpAndGoOnHook |
4 | goOnHookOnGlareDet |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ccasGCnfIndex An arbitrary index that uniquely identifies a
entry in the ccasIfExtGeneralConfigTable.
The index of 1 is reserved for the default entry. | column | Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.1 |
| ccasGCnfIncCallPosTwist This object specifies a positive power twist when the
power level of the high frequency component is set to
relatively higher than the low frequency component for
incoming ca… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.10 |
| ccasGCnfIncCallBreakThreshold This object specifies a power level which is used for
detection of on hook to off hook transition for incoming
call. | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.11 |
| ccasGCnfOutCallLoFreqPower This object specifies the power level of the low frequency
component for outgoing call.
The power level of the high frequency component of outgoing
call is relative above or be… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.12 |
| ccasGCnfOutCallPowerTwist This object specifies the relative power level of the
high frequency component for outgoing call.
When this object is set to 0, the power level of both
frequency components is set… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.13 |
| ccasGCnfOutCadenceOntime This object specifies the duration during which the digit
tone is generated for outgoing call. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.14 |
| ccasGCnfOutCadenceOfftime This object specifies the silence between digit tones
for outgoing call. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.15 |
| ccasGCnfCountryCode This object specifies the country code digits. | column | OctetString | .1.3.6.1.4.1.9.9.314.1.6.1.1.16 |
| ccasGCnfEchoCancellation This object specifies the echo cancellation mode, and
it is applicable to an outgoing R2 register. | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.17 |
| ccasGCnfSubscriberCategory This object specifies the subscriber category types:
. (1) subscriber without priority
. (2) subscriber with priority
. (3) maintenance equipment
. (4)… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.18 |
| ccasGCnfNatureOfCircuit This object specifies if there is any satellite link in
the path:
. (1) Satellite link is not included.
. (2) Satellite link is included. | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.19 |
| ccasGCnfCompelledSignalingType This object specifies the Compelled Signaling type:
. enbloc (1): The called number is forwarded in a block.
. overlap (2): The called numder is forwarded one at a time.
. endtoen… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.20 |
| ccasGCnfTxDigitOrder This object specifies the transmit digit order in which
ANI and DNIs will be dialled out when the controlling
application gives both the the calling party number and
the calle… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.21 |
| ccasGCnfDigitDetectMode This objects specifies the digit detect mode that the
GW should be opened with for reception of digits.
. dtmf (1): Dual tone multifrequency
. mf (2): Multifrequency
. dp (3): Di… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.22 |
| ccasGCnfMeteringRepIntThresh This object specifies the duration between two consecutive
metering pulses, if it changes more than value specified
in this parameter then an event will be triggered to MGC. | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.23 |
| ccasGCnfStartTimer This object specifies the amount of time that the GW
must wait for receiving digits after generating the
seize ACK or start dial indication for an incoming
call.
The value of … | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.24 |
| ccasGCnfLongTimer This object specifies the period between receiving
digits. The timer is not started until the first digit
is received.
The GW starts this timer during digit collection when
at … | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.25 |
| ccasGCnfShortTimer This object specifies the period between receiving
digits.
The GW starts this timer during digit collection when
the digit string that it has collected matches at least
one pat… | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.26 |
| ccasGCnfLongDurationTimer This object specifies long duration event when placed
in front of a digit. It indicates that that position is
satisfied only if the duration of the event exceeds the
long-durat… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.27 |
| ccasGCnfMGCTimer This object specifies the timer in the GW waiting for
the MGC to provide the rest of the information for CAS
signaling.
During overlap CAS signaling, for an outgoing call, the
MGC… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.28 |
| ccasGCnfDigitType This object specifies the digit type to pulsed from the
GW such as:
.dtmf - Dual tone multifrequency.
.mf - Multifrequency.
.dp - Dial pulse.
This parameter can be overridd… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.29 |
| ccasGCnfParmSource This object indicates whether GW should read the CAS
related timer parameters from the CAS Variant file
downloaded for that endpoint or to read from the MIB.
This gives the fle… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.3 |
| ccasGCnfEndPointDirectional This object specifies the direction in which CAS calls
will be accepted on this endpoint.
.bidirectional - Accepts both incoming and outgoing calls.
.incoming - Accepts incoming… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.30 |
| ccasGCnfPulseReceiveTimeout This object specifies the time that the MG should wait
for the receipt of pulse (on hook pulse or off hook
pulse).
The value of 0 indicates the timer will not be started
and MG… | column | seconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.31 |
| ccasGCnfInitialDelay This object specifies the initial delay that must be applied
on an outgoing trunk before the digits are pulse out.
The value of 0 indicates the timer, ccasGCnfInitialDelay
will s… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.32 |
| ccasGCnfMaxNumCallParty This object specifies the maximum number of calling party
digits to collect for reporting to the MGC.
The MGC can overridden this value, and a value of 0 indicates
that there is … | column | Unsigned32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.33 |
| ccasGCnfRowStatus This object is used for adding, modifying, deleting the
entries from the ccasExtIfGeneralConfigTable.
A default entry with index value 1 is created at
initialization, and it ca… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.314.1.6.1.1.34 |
| ccasGCnfRegSigMode This object specifies the register signaling mode for a
R2 registers. | column | CASRegisterSignal | .1.3.6.1.4.1.9.9.314.1.6.1.1.4 |
| ccasGCnfLineSigType This object specifies the line signaling type that will be
used for the R2 line signaling.
. digital (1): The digital line signaling is typically used
for PCM systems. Only … | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.5 |
| ccasGCnfRingBackType This object specifies the ring back signal type of FGD
protocol.
. wink (1): A pulse which is a timed transition from on
hook to off hook and back to on hook.
. wink and tone… | column | Enumeration | .1.3.6.1.4.1.9.9.314.1.6.1.1.6 |
| ccasGCnfIncCallHiFreqPower This object specifies the power of the high frequency signal
component for incoming call. | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.7 |
| ccasGCnfIncCallLoFreqPower This object specifies the power of the low frequency signal
component for incoming call. | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.8 |
| ccasGCnfIncCallNegTwist This object specifies a negative power twist when the
power level of the low frequency component is set to
relatively higher than the high frequency component
for incoming ca… | column | dBm Integer32 | .1.3.6.1.4.1.9.9.314.1.6.1.1.9 |