cApsConfigYcable

CISCO-APS-EXT-MIB · .1.3.6.1.4.1.9.10.72.1.2.1.2

Object

column r/w Enumeration

The Y-cable configuration for the APS group associated with
user channels.
              
noYcable
              
The APS channels in the APS group are not connected to an
external Y-cable.
              
ycable
              
Two user-side interfaces (not necessarily SONET or CDL) are
connected to an external y-cable and are grouped into an APS
group for endToEnd APS. The received user signal is split
in the y-cable coupler and is received on both the interfaces.
However, only one interface must transmit toward the user at any
given time. With cApsConfigYcable set to 'ycable', the
cApsConfigSpan must be set to 'endToEnd'. There must be
only two APS channels in an APS group with cApsConfigYcable
set to 'ycable'.
              
ycableXconnectCommon
              
This refers to a configuration where two user-side interfaces
are connected to an external y-cable. The two signals received
on these interface are connected to the same cross connect in
the switch. The switch fabric selects one of the two received
signals, duplicates it, and forwards it to two network side
interfaces grouped for 1+1 linear APS. The received signal from
the network side is transmitted to only one user-side interface.
cApsConfigSpan is ignored if cApsConfigYcable is set to
'ycableXconnectCommon'. There must be only two APS channels in
an APS group with cApsConfigYcable set to
'ycableXconnectCommon'.
              
This object may not be modified if the associated
cApsConfigRowStatus object is equal to 'active'.
              
If this object is set to 'ycable' or 'ycableXconnectCommon',
the user must shut one of the two channels before setting
cApsConfigRowStatus to 'notInService'.

Context

MIB: CISCO-APS-EXT-MIB
OID: .1.3.6.1.4.1.9.10.72.1.2.1.2
Type: column
Access: readwrite
Status: current
Parent: cApsConfigExtEntry
Table: cApsConfigExtTable
Siblings: 11

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	noYcable
`2`	ycable
`3`	ycableXconnectCommon

Related Objects

Sibling Objects

Object	Type	Syntax	OID
cApsConfigSpan The span (hopByHop or endToEnd) for the APS group. hopByHop This refers to linear APS, e.g. linear SONET APS, or hopByHop CDL APS. In a DWDM system, …	column	Enumeration	`.1.3.6.1.4.1.9.10.72.1.2.1.1`
cApsConfigFarEndGroupName The value specified in this object applies when the value of cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'. APS messages, used to support bidirectional or li…	column	OctetString	`.1.3.6.1.4.1.9.10.72.1.2.1.10`
cApsConfigFarEndIpAddressType This object can be set only when the value of cApsConfigMessageTransport is 'ip'. This object specifies the type of IP address defined in cApsConfigFarEndIpAddress.	column	INET-ADDRESS-MIBInetAddressType	`.1.3.6.1.4.1.9.10.72.1.2.1.11`
cApsConfigFarEndIpAddress This object can be set only when the value of cApsConfigMessageTransport is 'ip'. This object specifies the IP address of the far end, which is used as the destinat…	column	INET-ADDRESS-MIBInetAddress	`.1.3.6.1.4.1.9.10.72.1.2.1.12`
cApsConfigMinSearchUpInterval This object is instantiated only when the standby interface is not monitored. If both interfaces go down and the standby interface is not monitored, successive switchovers may be …	column	Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.3`
cApsConfigMaxSearchUpInterval This object is instantiated only when the standby interface is not monitored. If both interfaces go down and the standby interface is not monitored, successive switchovers may be …	column	seconds Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.4`
cApsConfigSwitchoverEnableInterval This object specifies the value of the timer to control the minimum interval between switchovers. After a switchover, APS is re-enabled only after this amount of time has elapsed,…	column	seconds Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.5`
cApsConfigMessageTransport This object specifies the type of transport configured for exchange of APS protocol messages. The type of transport currently being used is indicated in the cApsStatusMessageTran…	column	CApsMessageTransport	`.1.3.6.1.4.1.9.10.72.1.2.1.6`
cApsConfigMessageHolddown The value specified in this object applies when the value of cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'. APS messages are exchanged between systems to supp…	column	milliseconds Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.7`
cApsConfigMessageHolddownCount The value specified in this object applies when the value of cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'. The maximum number of APS messages that can be sen…	column	Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.8`
cApsConfigMessageMaxInterval The value specified in this object applies when the value of cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'. An APS message is sent unconditionally, whenever t…	column	milliseconds Integer32	`.1.3.6.1.4.1.9.10.72.1.2.1.9`