cApsConfigMaxSearchUpInterval
CISCO-APS-EXT-MIB ·
.1.3.6.1.4.1.9.10.72.1.2.1.4
Object
column
r/w
seconds Integer32
This object is instantiated only when the standby interface
is not monitored. If both interfaces go down and the standby
interface is not monitored, successive switchovers may be used
in order to search for an interface that is up.
This object specifies the maximum time interval between
switchovers when both interfaces go down.
Context
- MIB
- CISCO-APS-EXT-MIB
- OID
.1.3.6.1.4.1.9.10.72.1.2.1.4- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- cApsConfigExtEntry
- Table
- cApsConfigExtTable
- Siblings
- 11
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 1-120
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cApsConfigSpan The span (hopByHop or endToEnd) for the APS group.
hopByHop
This refers to linear APS, e.g. linear SONET APS, or hopByHop
CDL APS. In a DWDM system, … | column | Enumeration | .1.3.6.1.4.1.9.10.72.1.2.1.1 |
| cApsConfigFarEndGroupName The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
APS messages, used to support bidirectional or li… | column | OctetString | .1.3.6.1.4.1.9.10.72.1.2.1.10 |
| cApsConfigFarEndIpAddressType This object can be set only when the value of
cApsConfigMessageTransport is 'ip'.
This object specifies the type of IP address defined
in cApsConfigFarEndIpAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.10.72.1.2.1.11 |
| cApsConfigFarEndIpAddress This object can be set only when the value of
cApsConfigMessageTransport is 'ip'.
This object specifies the IP address of the far end, which is
used as the destinat… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.10.72.1.2.1.12 |
| cApsConfigYcable The Y-cable configuration for the APS group associated with
user channels.
noYcable
The APS channels in the APS group are not connected to an
externa… | column | Enumeration | .1.3.6.1.4.1.9.10.72.1.2.1.2 |
| cApsConfigMinSearchUpInterval This object is instantiated only when the standby interface
is not monitored. If both interfaces go down and the standby
interface is not monitored, successive switchovers may be … | column | Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.3 |
| cApsConfigSwitchoverEnableInterval This object specifies the value of the timer to control
the minimum interval between switchovers. After a switchover,
APS is re-enabled only after this amount of time has elapsed,… | column | seconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.5 |
| cApsConfigMessageTransport This object specifies the type of transport configured for
exchange of APS protocol messages. The type of transport
currently being used is indicated in the
cApsStatusMessageTran… | column | CApsMessageTransport | .1.3.6.1.4.1.9.10.72.1.2.1.6 |
| cApsConfigMessageHolddown The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
APS messages are exchanged between systems to supp… | column | milliseconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.7 |
| cApsConfigMessageHolddownCount The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
The maximum number of APS messages that can be sen… | column | Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.8 |
| cApsConfigMessageMaxInterval The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
An APS message is sent unconditionally, whenever t… | column | milliseconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.9 |