cApsConfigFarEndIpAddressType
CISCO-APS-EXT-MIB ·
.1.3.6.1.4.1.9.10.72.1.2.1.11
Object
This object can be set only when the value of
cApsConfigMessageTransport is 'ip'.
This object specifies the type of IP address defined
in cApsConfigFarEndIpAddress.
Context
- MIB
- CISCO-APS-EXT-MIB
- OID
.1.3.6.1.4.1.9.10.72.1.2.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cApsConfigExtEntry
- Table
- cApsConfigExtTable
- Siblings
- 11
Syntax
INET-ADDRESS-MIBInetAddressType
- Source
- INET-ADDRESS-MIBInetAddressType
- Base type
Enumeration
Values & Constraints
Type Values
0 | unknown |
1 | ipv4 |
2 | ipv6 |
3 | ipv4z |
4 | ipv6z |
16 | dns |
25 | l2vpn |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cApsConfigSpan The span (hopByHop or endToEnd) for the APS group.
hopByHop
This refers to linear APS, e.g. linear SONET APS, or hopByHop
CDL APS. In a DWDM system, … | column | Enumeration | .1.3.6.1.4.1.9.10.72.1.2.1.1 |
| cApsConfigFarEndGroupName The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
APS messages, used to support bidirectional or li… | column | OctetString | .1.3.6.1.4.1.9.10.72.1.2.1.10 |
| cApsConfigFarEndIpAddress This object can be set only when the value of
cApsConfigMessageTransport is 'ip'.
This object specifies the IP address of the far end, which is
used as the destinat… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.10.72.1.2.1.12 |
| cApsConfigYcable The Y-cable configuration for the APS group associated with
user channels.
noYcable
The APS channels in the APS group are not connected to an
externa… | column | Enumeration | .1.3.6.1.4.1.9.10.72.1.2.1.2 |
| cApsConfigMinSearchUpInterval This object is instantiated only when the standby interface
is not monitored. If both interfaces go down and the standby
interface is not monitored, successive switchovers may be … | column | Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.3 |
| cApsConfigMaxSearchUpInterval This object is instantiated only when the standby interface
is not monitored. If both interfaces go down and the standby
interface is not monitored, successive switchovers may be … | column | seconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.4 |
| cApsConfigSwitchoverEnableInterval This object specifies the value of the timer to control
the minimum interval between switchovers. After a switchover,
APS is re-enabled only after this amount of time has elapsed,… | column | seconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.5 |
| cApsConfigMessageTransport This object specifies the type of transport configured for
exchange of APS protocol messages. The type of transport
currently being used is indicated in the
cApsStatusMessageTran… | column | CApsMessageTransport | .1.3.6.1.4.1.9.10.72.1.2.1.6 |
| cApsConfigMessageHolddown The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
APS messages are exchanged between systems to supp… | column | milliseconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.7 |
| cApsConfigMessageHolddownCount The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
The maximum number of APS messages that can be sen… | column | Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.8 |
| cApsConfigMessageMaxInterval The value specified in this object applies when the value of
cApsStatusMessageTransport is 'dcc', 'ip', or 'osc'.
An APS message is sent unconditionally, whenever t… | column | milliseconds Integer32 | .1.3.6.1.4.1.9.10.72.1.2.1.9 |