cienaCesBenchmarkProfileEntryCColor
CIENA-CES-BENCHMARK-MIB ·
.1.3.6.1.4.1.1271.2.1.39.1.1.11.1.26
Object
column
r/w
CienaCesBenchmarkColorTest
Color of the C-VLAN tag for the test traffic. This is directly related to the value of the DEI bit configured in the VLAN tag of the test traffic. Green traffic will have its DEI bit set to 0 while Yellow traffic will have its DEI bit set to 1. Green test traffic is generated based on the bandwidth configured in the test profile. Yellow traffic is generated based on the excess-bandwidth parameter. Finally, if the user selects green-yellow-red, the yellow traffic is generated at 1.25 * excess-bandwidth. This is used only when encapType is set to dot1q. In a QinQ configuration, the c-dei bit is set to the same value as the s-dei bit in order to simplify software.
Context
- MIB
- CIENA-CES-BENCHMARK-MIB
- OID
.1.3.6.1.4.1.1271.2.1.39.1.1.11.1.26- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cienaCesBenchmarkProfileEntry
- Table
- cienaCesBenchmarkProfileTable
- Siblings
- 42
Syntax
CienaCesBenchmarkColorTest
- Source
- CienaCesBenchmarkColorTest
- Base type
Enumeration
Values & Constraints
Type Values
1 | green |
2 | yellow |
3 | greenYellow |
4 | greenYellowRed |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cienaCesBenchmarkProfileEntryId Index for BENCHMARK profile records. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.1 |
| cienaCesBenchmarkProfileEntrySamplingInterval For the latency and PDV tests, this is the interval,
in 100ms, to wait between samples. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.10 |
| cienaCesBenchmarkProfileEntryFrameLossStartBw For the frame loss test, this indicates which bandwidth
value to use as the starting bandwidth; the maximum
bandwidth determined via the throughput test, the
bandwidth parameter c… | column | Enumeration | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.11 |
| cienaCesBenchmarkProfileEntryVidValidation Indicates whether VID validation is performed in
the classifier or not on the returning packet. If vid
validation is set to false, PCP and Color validation are
ignored and automa… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.12 |
| cienaCesBenchmarkProfileEntryPcpValidation Used to indicate whether the PCP value of the
test packet should be used to classifier the reflected
packets or not. When color remarking is used, this should
be set to false. Def… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.13 |
| cienaCesBenchmarkProfileEntryColorValidation Used to indicate whether the color bit of the
test packet should be used to classifier the reflected
packets or not. In color unaware testing, this should
be set to false. Default… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.14 |
| cienaCesBenchmarkProfileEntryKpiProfileId Name of a valid KPI profile, from the
cienaCesBenchmarkKpiProfileTable, to use when
analysing the test results for this profile. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.15 |
| cienaCesBenchmarkProfileEntryBwAllocProfileId Id of a valid Bandwidth Allocation profile,
from the cienaCesBenchmarkBwAllocProfileTable,
used for distributing the profile bandwidth amongst
the configured PCP values for this p… | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.16 |
| cienaCesBenchmarkProfileEntryEmixSequenceId Id of a valid EMIX sequence configured in the
cienaCesBenchmarkEmixSequenceTable, to use when y1564
is selected. The EMIX sequence is used instead of the
frame size list if and on… | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.17 |
| cienaCesBenchmarkProfileEntryEncapType Encapsulation type to use for generated packets. | column | Enumeration | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.18 |
| cienaCesBenchmarkProfileEntryPduType Vlan tag protocol identifier to use for the generated packets. | column | Enumeration | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.19 |
| cienaCesBenchmarkProfileEntryName Name of the profile as entered when created. | column | OctetString | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.2 |
| cienaCesBenchmarkProfileEntryDstmac MAC address to use as the destination MAC address on
the generated packets. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.20 |
| cienaCesBenchmarkProfileEntrySVid S-VLAN ID to used for generated packets when encapType is set to QinQ | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.21 |
| cienaCesBenchmarkProfileEntrySPcp Bitmap of the S-VLAN PCP (Priority Code Point) value to
test with. When RFC2544 test is enabled, only one
PCP can be set in the mask. Otherwise, a test session
will be run for e… | column | CienaCesBenchmarkPcpBitmap | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.22 |
| cienaCesBenchmarkProfileEntrySColor Color of the S-VLAN tag for the test traffic. This is
directly related to the value of the DEI bit
configured in the VLAN tag of the test traffic. Green
traffic will have its DE… | column | CienaCesBenchmarkColorTest | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.23 |
| cienaCesBenchmarkProfileEntryCVid C-VLAN ID to used for generated packets when encapType is set to
QinQ or dot1q. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.24 |
| cienaCesBenchmarkProfileEntryCPcp Bitmap of the C-VLAN PCP (Priority Code Point) value to
test with. When RFC2544 test is enabled, only one
PCP can be set in the mask. Otherwise, a test session
will be run for e… | column | CienaCesBenchmarkPcpBitmap | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.25 |
| cienaCesBenchmarkProfileEntryTpid Vlan tag protocol identifier to use for the generated packets.
The following TPID values are supported by benchmark:
0x8100
0x9100
0x88A8 | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.27 |
| cienaCesBenchmarkProfileEntryDscp IP DSCP value to use for the generated packets. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.28 |
| cienaCesBenchmarkProfileEntrySrcInetAddrType Specifies the type of address cienaCesBenchmarkProfileEntrySrcInetAddr belongs to.
When set to:
ipv4 : cienaCesBenchmarkProfileEntrySrcInetAddr should be compliant with
… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.29 |
| cienaCesBenchmarkProfileEntryBandwidth Maximum bandwidth to use when generating green test
traffic for the profile. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.3 |
| cienaCesBenchmarkProfileEntrySrcInetAddr Specifies the unicast source IP address to use in IP test packet.
The InetAddress specified here is compliant with RFC 4001.
The InetAddressType and the InetAddress must be set as… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.30 |
| cienaCesBenchmarkProfileEntryDstInetAddrType Specifies the type of address cienaCesBenchmarkProfileEntryDstInetAddr belongs to.
When set to:
ipv4 : cienaCesBenchmarkProfileEntryDstInetAddr should be compliant with
… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.31 |
| cienaCesBenchmarkProfileEntryDstInetAddr Specifies the unicast destination IP address to use in IP test packet.
The InetAddress specified here is compliant with RFC 4001.
The InetAddressType and the InetAddress must be s… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.32 |
| cienaCesBenchmarkProfileEntryCustomPayload Custom payload to be used on the generated packets. | column | OctetString | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.33 |
| cienaCesBenchmarkProfileEntryThroughputTest Run throughput test | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.34 |
| cienaCesBenchmarkProfileEntryFramelossTest Run frame loss test | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.35 |
| cienaCesBenchmarkProfileEntryLatencyTest Run latency test | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.36 |
| cienaCesBenchmarkProfileEntryPdvTest Run packet delay variation test | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.37 |
| cienaCesBenchmarkProfileEntryBurstTest Run packet burst test | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.38 |
| cienaCesBenchmarkProfileEntryRfc2544Suite Run RFC2544 test suite which includes throughput, frame
loss and latency tests | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.39 |
| cienaCesBenchmarkProfileEntryExcessBandwidth Maximum bandwidth to use when generating yellow test
traffic for the profile. When testing for red color,
this bandwidth is multiplied by 1.25 | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.4 |
| cienaCesBenchmarkProfileEntryY1564Test The Y1564 test includes the throughput, frameloss,
latency and PDV tests are is run using the configured
EMIX sequence. If the profile's EMIX sequence is
not configured, the defau… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.40 |
| cienaCesBenchmarkProfileEntryHwSessionsRequired This represents the number of hardware sessions
required to enable/run a test instance using
this profile according to the profile's current
configuration.
One hardware session … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.41 |
| cienaCesBenchmarkProfileEntryNumOfRef Number of generator test instances currently
using this test profile for testing. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.42 |
| cienaCesBenchmarkProfileEntryRowStatus Used to manage the creation and deletion of the
conceptual rows in this table. To create a row in
this table, set this object to 'createAndGo'.
To delete a row in this table, se… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.43 |
| cienaCesBenchmarkProfileEntryInterval Interval between the start of one test group to the start
of the next test group. | column | Enumeration | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.5 |
| cienaCesBenchmarkProfileEntryDuration Duration of the testing. The test group is repeated until
the duration ends. When indefinite is set, test group is
run only once to completion | column | Enumeration | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.6 |
| cienaCesBenchmarkProfileEntrySetFrameSizeList Used to replace the existing frame size table with the specified list.
More than one values can be listed and are separated by commas. | column | OctetString | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.7 |
| cienaCesBenchmarkProfileEntryMaxSearches For the throughput test, this is the maximum number of
searches to find a transmit rate without drops for a
given frame size. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.8 |
| cienaCesBenchmarkProfileEntryMaxSamples For the latency and PDV tests, this is the number of
samples to take in order to determine the min, avg
and max latency and avg PDV. | column | Integer32 | .1.3.6.1.4.1.1271.2.1.39.1.1.11.1.9 |