wirelessReceiveSignalStatus
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.26.10
Object
scalar
Enumeration
The Wireless Receive Signal Status indicates if the receiver is able to demodulate the transmit signal from the remote end of the link. If it cannot demodulate the signal, a protection switch may occur in a system configured for 1+1 Hot Standby.
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.26.10- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- protectionStatus
- Siblings
- 31
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | ok |
1 | notDetected |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| licensedTransmitCapacityStatus In a 1+1 Hot Standby configuration, the Licensed
Transmit Capacity Status attribute indicates when the
Licensed Transmit Capacity is below that of its
neighbor. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.14 |
| dataPortEthernetSpeedStatus In a 1+1 Hot Standby configuration, the Data Port
Ethernet Speed Status attribute indicates if the Ethernet
Speed of the Data Port is below that of its neighbor. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.15 |
| managementPortEthernetSpeedStatus In a 1+1 Hot Standby configuration, the Management Port
Ethernet Speed Status attribute indicates if the Ethernet
Speed of the Management Port is below that of its
neighbor. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.16 |
| protectionInterfaceStatus In a 1+1 Hot Standby configuration, information is
shared between neighbor CMUs over the Protection
Interface. The Protection Interface Status attribute
reports whether the nei… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.17 |
| remotePrimaryIPAddress In a 1+1 Hot Standby configuration, the Remote Primary
IP Address reports the IP address of the CMU which is
configured as Primary at the remote end of the wireless
link. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.18 |
| remoteSecondaryIPAddress In a 1+1 Hot Standby configuration, the Remote Secondary
IP Address reports the IP address of the CMU which is
configured as Secondary at the remote end of the wireless
link. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.19 |
| protectionAvailabilityStatus In a 1+1 Hot Standby configuration, the Protection
Availability Status attribute indicates whether the
Active unit is currently being protected by the Inactive
unit. If it isn'… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.2 |
| remotePrimaryMACAddress In a 1+1 Hot Standby configuration, the Remote Primary
MAC Address reports the MAC address of the CMU which is
configured as Primary at the remote end of the wireless
link. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.20 |
| remoteSecondaryMACAddress In a 1+1 Hot Standby configuration, the Remote Secondary
MAC Address reports the MAC address of the CMU which is
configured as Secondary at the remote end of the wireless
link. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.21 |
| remotePrimarySecondaryMode In a 1+1 Hot Standby configuration, this attribute
identifies whether the Active Unit at the remote end of
the link is configured as Primary or Secondary. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.22 |
| transmitterStatus Indicates whether the RFU is transmitting or muted. In a
1+1 Hot Standby configuration, it will also indicate if
the RFU is Inactive and therefore ready to transmit. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.23 |
| endWirelessReceiveSignalStatus The End Wireless Receive Signal Status indicates if the
end of a link is unable to demodulate the signal
transmitted from the remote end of the link. When
Protection is set to … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.26 |
| rxDiversityDataPortStatus When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
Before sending these frames, the Data Port MUST be
negotiated at 1000 … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.27 |
| rxDiversityAvailabilityStatus The Rx Diversity Availability Status attribute will
indicate when Receive Diversity is not operating
correctly, either due to a fault or due to an incorrect
configuration | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.28 |
| rxDiversityConfigurationStatus For Receive Diversity to operate correctly, certain
attributes must be configured correctly on both neighbor
CMUs. The Rx Diversity Configuration Status attribute
will indicate… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.29 |
| protectionConfigurationStatus In a 1+1 Hot Standby configuration, this attribute will
indicate whether the configuration will support
protection. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.3 |
| rxDiversityNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must both be configured with the Protection
attribute set to �1+1 Hot Standby with Rx Diversity�.
The Rx Diversit… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.30 |
| rxDiversityVlanTpidNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must be configured with the same value of
Rx Diversity VLAN TPID. The Rx Diversity VLAN TPID
Neighbor Compatibili… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.31 |
| rxDiversityVidNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must be configured with the same value of
Rx Diversity VID. The Rx Diversity VID Neighbor
Compatibility attribute… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.32 |
| neighborInternetAddressType The type of Internet address specified by the associated
neighborInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.33 |
| neighborInternetAddress In a 1+1 Hot Standby configuration, the Neighbor
Internet Address identifies the INET Address of the
neighbor CMU connected via the Protection Interface. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.34 |
| remotePrimaryInternetAddressType The type of Internet address specified by the associated
remoteSecondaryInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.35 |
| remotePrimaryInternetAddress In a 1+1 Hot Standby configuration, the Remote Primary
Internet Address reports the INET address of the CMU
which is configured as Primary at the remote end of the
wireless lin… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.36 |
| remoteSecondaryInternetAddressType The type of Internet address specified by the associated
remoteSecondaryInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.37 |
| remoteSecondaryInternetAddress In a 1+1 Hot Standby configuration, the Remote Secondary
Internet Address reports the INET address of the CMU
which is configured as Secondary at the remote end of the
wireless… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.38 |
| protectionState In a 1+1 Hot Standby configuration, only one CMU / RFU
at a given end of the link is Active at any one time, the
neighbor CMU / RFU being Inactive. The Protection State
attribu… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.4 |
| activeUnit At a given end of a 1+1 Hot Standby configuration, one
CMU must be configured as Primary, the other CMU as
Secondary. When a Protected Link initialises with no
faults, the CMU … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.5 |
| protectionSwitchCause In a 1+1 Hot Standby configuration, the Protection
Switch Cause attribute reports the reason for the last
protection switch. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.6 |
| endId In a 1+1 Hot Standby configuration, the End Id contains
the IP address of neighboring CMUs starting with the
highest IP address and with a space separating the
addresses. It is… | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.7 |
| neighborIPAddress In a 1+1 Hot Standby configuration, the Neighbor IP
Address identifies the IP Address of the neighbor CMU
connected via the Protection Interface. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.8 |
| neighborMACAddress In a 1+1 Hot Standby configuration, the Neighbor MAC
Address identifies the MAC Address of the neighbor CMU
connected via the Protection Interface. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.9 |