rFURFSwitchAlarm
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.23.28
Object
scalar
Enumeration
This indicates that an RF switch is not present when it should be or that on the most recent attempt to make this unit active, the IRFU RF Switch was not able to switch to the correct position
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.23.28- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- rfu
- Siblings
- 37
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | ok |
1 | fault |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| rFURfBand RFU RF band in MHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.1 |
| rFUSerial RFU serial number | scalar | OctetString | .1.3.6.1.4.1.17713.8.23.10 |
| rFUActiveFirmwareBank RFU active firmware bank number | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.11 |
| rFUVersionBank1 RFU firmware version number (nnn/ddMMYY) in bank 1 | scalar | OctetString | .1.3.6.1.4.1.17713.8.23.12 |
| rFUVersionBank2 RFU firmware version number (nnn/ddMMYY) in bank 2 | scalar | OctetString | .1.3.6.1.4.1.17713.8.23.13 |
| rFUType RFU type as: RFU platform, frequency band, Tx-Rx
frequency spacing, Hi/Lo band and transmit frequency
range | scalar | OctetString | .1.3.6.1.4.1.17713.8.23.14 |
| rFURxRFSynthLockAlarm RFU RF receiver out of lock alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.15 |
| rFUTxRFSynthLockAlarm RFU RF transmitter out of lock alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.16 |
| rFUTxPowerAlarm RFU transmitter output failed alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.17 |
| rFUCommonIFSynthLockAlarm Alarm indicating when the common IF RFU synthesizer is
out of lock | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.18 |
| rFUPowerAlarm RFU general power alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.19 |
| rFUTxBandAboveRx Yes means RFU transmitter frequency band is above
receiver frequency band | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.2 |
| rFULockoutAlarm RFU locked pending unlock code alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.20 |
| rFUCableAlarm RFU cable detector voltage out of range alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.21 |
| rFUCableAttenuationAdjustAlarm RFU cable attenuator not yet adjusted alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.22 |
| rFUTxPowerDegradedAlarm Indicates when the current transmit power is more than 3
dB below or more than 3 dB above the correct transmit
power. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.23 |
| rFURpsAlarm RFU radio protection switch (RPS) alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.24 |
| rFUTxMuteStatus Indicates whether the RFU is transmitting or muted. If
it is muted, it will also indicate the reason. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.25 |
| rFUFanAssemblyAlarm This indicates when the IRFU transceiver fan assembly
has failed. The assembly consists of two fans and if one
fan fails, the this will report partial failure. If both
fans fai… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.26 |
| rFUHighTemperatureAlarm Indicates when the temperature of the IRFU transceiver
has risen above either of two thresholds. If the
temperature exceeds the High Temperature threshold, the
transmit power m… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.27 |
| rFURxIFSynthLockAlarm RFU IF receiver out of lock alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.29 |
| rFUFreqSpacing Tx-Rx frequency spacing in kHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.3 |
| rFUTxIFSynthLockAlarm RFU IF transmitter out of lock alarm | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.30 |
| rFUPowerButtonPressed IRFU power button have been pressed, IFRU has powered
down unexpectedly | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.31 |
| rFUConnectedPlatform The type of RFU platform currently connected to the CMU | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.32 |
| rFUCommonRFSynthLockAlarm Alarm indicating when the common RFU RF synthesizer is
out of lock | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.33 |
| rFUBranchingConfiguration When an IRFU is being installed, the configuration of
the IRFU branching unit must be configured. Please see
the User Guide for further details | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.34 |
| rFUTransceiverLocation When a 2+0 IRFU is being installed, the user must
configure which of the two IRFU transceivers the CMU is
controlling in order to ensure correct operation | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.35 |
| rFURfSwitchCableAlarm The RF switch in the IRFU is indicating an invalid
switch position. The most likely cause is a fault or a
disconnection of the cable which connects the transceiver
to the RF sw… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.23.36 |
| rFUReceiveBranchingUnitLoss The receive loss in the IRFU branching unit, expressed
in tenths of a dB. The branching unit is a component of
the IRFU which is situated between the IRFU transceiver
and IRFU … | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.17713.8.23.37 |
| rFUTransmitBranchingUnitLoss The transmit loss in the IRFU branching unit, expressed
in tenths of a dB. The branching unit is a component of
the IRFU which is situated between the IRFU transceiver
and IRFU… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.17713.8.23.38 |
| rFUTxPowerMin Minimum transmitter power level, in 10ths of dBm | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.4 |
| rFUTxPowerMax Maximum transmitter power level, in 10ths of dBm | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.5 |
| rFURxFreqMin Minimum receiver frequency in kHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.6 |
| rFURxFreqMax Maximum receiver frequency in kHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.7 |
| rFUTxFreqMin Minimum transmitter frequency in kHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.8 |
| rFUTxFreqMax Maximum transmitter frequency in kHz | scalar | Integer32 | .1.3.6.1.4.1.17713.8.23.9 |