rFUBranchingConfiguration

CAMBIUM-PTP800-MIB · .1.3.6.1.4.1.17713.8.23.34
MIB view Table view

Object

scalar r/w Enumeration 
When an IRFU is being installed, the configuration of 
the IRFU branching unit must be configured. Please see 
the User Guide for further details

Context

MIB
CAMBIUM-PTP800-MIB
OID
.1.3.6.1.4.1.17713.8.23.34
Type
scalar
Access
readwrite
Status
current
Parent
rfu
Siblings
37

Syntax

Enumeration

Values & Constraints

Enumerated Values
0rFU1plus0
1rFU1plus0MHSBReadyEqual
2rFU1plus0MHSBReadyUnequal
3rFU1plus1MHSBEqual
4rFU1plus1MHSBUnequal
5rFU1plus1TxMHSBRxSD
6rFU2plus0

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
rFURfBand
RFU RF band in MHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.1
rFUSerial
RFU serial number
scalarOctetString.1.3.6.1.4.1.17713.8.23.10
rFUActiveFirmwareBank
RFU active firmware bank number
scalarInteger32.1.3.6.1.4.1.17713.8.23.11
rFUVersionBank1
RFU firmware version number (nnn/ddMMYY) in bank 1
scalarOctetString.1.3.6.1.4.1.17713.8.23.12
rFUVersionBank2
RFU firmware version number (nnn/ddMMYY) in bank 2
scalarOctetString.1.3.6.1.4.1.17713.8.23.13
rFUType
RFU type as: RFU platform, frequency band, Tx-Rx frequency spacing, Hi/Lo band and transmit frequency range
scalarOctetString.1.3.6.1.4.1.17713.8.23.14
rFURxRFSynthLockAlarm
RFU RF receiver out of lock alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.15
rFUTxRFSynthLockAlarm
RFU RF transmitter out of lock alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.16
rFUTxPowerAlarm
RFU transmitter output failed alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.17
rFUCommonIFSynthLockAlarm
Alarm indicating when the common IF RFU synthesizer is out of lock
scalarEnumeration.1.3.6.1.4.1.17713.8.23.18
rFUPowerAlarm
RFU general power alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.19
rFUTxBandAboveRx
Yes means RFU transmitter frequency band is above receiver frequency band
scalarEnumeration.1.3.6.1.4.1.17713.8.23.2
rFULockoutAlarm
RFU locked pending unlock code alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.20
rFUCableAlarm
RFU cable detector voltage out of range alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.21
rFUCableAttenuationAdjustAlarm
RFU cable attenuator not yet adjusted alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.22
rFUTxPowerDegradedAlarm
Indicates when the current transmit power is more than 3 dB below or more than 3 dB above the correct transmit power.
scalarEnumeration.1.3.6.1.4.1.17713.8.23.23
rFURpsAlarm
RFU radio protection switch (RPS) alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.24
rFUTxMuteStatus
Indicates whether the RFU is transmitting or muted. If it is muted, it will also indicate the reason.
scalarEnumeration.1.3.6.1.4.1.17713.8.23.25
rFUFanAssemblyAlarm
This indicates when the IRFU transceiver fan assembly has failed. The assembly consists of two fans and if one fan fails, the this will report partial failure. If both fans fai…
scalarEnumeration.1.3.6.1.4.1.17713.8.23.26
rFUHighTemperatureAlarm
Indicates when the temperature of the IRFU transceiver has risen above either of two thresholds. If the temperature exceeds the High Temperature threshold, the transmit power m…
scalarEnumeration.1.3.6.1.4.1.17713.8.23.27
rFURFSwitchAlarm
This indicates that an RF switch is not present when it should be or that on the most recent attempt to make this unit active, the IRFU RF Switch was not able to switch to the …
scalarEnumeration.1.3.6.1.4.1.17713.8.23.28
rFURxIFSynthLockAlarm
RFU IF receiver out of lock alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.29
rFUFreqSpacing
Tx-Rx frequency spacing in kHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.3
rFUTxIFSynthLockAlarm
RFU IF transmitter out of lock alarm
scalarEnumeration.1.3.6.1.4.1.17713.8.23.30
rFUPowerButtonPressed
IRFU power button have been pressed, IFRU has powered down unexpectedly
scalarEnumeration.1.3.6.1.4.1.17713.8.23.31
rFUConnectedPlatform
The type of RFU platform currently connected to the CMU
scalarEnumeration.1.3.6.1.4.1.17713.8.23.32
rFUCommonRFSynthLockAlarm
Alarm indicating when the common RFU RF synthesizer is out of lock
scalarEnumeration.1.3.6.1.4.1.17713.8.23.33
rFUTransceiverLocation
When a 2+0 IRFU is being installed, the user must configure which of the two IRFU transceivers the CMU is controlling in order to ensure correct operation
scalarEnumeration.1.3.6.1.4.1.17713.8.23.35
rFURfSwitchCableAlarm
The RF switch in the IRFU is indicating an invalid switch position. The most likely cause is a fault or a disconnection of the cable which connects the transceiver to the RF sw…
scalarEnumeration.1.3.6.1.4.1.17713.8.23.36
rFUReceiveBranchingUnitLoss
The receive loss in the IRFU branching unit, expressed in tenths of a dB. The branching unit is a component of the IRFU which is situated between the IRFU transceiver and IRFU …
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.17713.8.23.37
rFUTransmitBranchingUnitLoss
The transmit loss in the IRFU branching unit, expressed in tenths of a dB. The branching unit is a component of the IRFU which is situated between the IRFU transceiver and IRFU…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.17713.8.23.38
rFUTxPowerMin
Minimum transmitter power level, in 10ths of dBm
scalarInteger32.1.3.6.1.4.1.17713.8.23.4
rFUTxPowerMax
Maximum transmitter power level, in 10ths of dBm
scalarInteger32.1.3.6.1.4.1.17713.8.23.5
rFURxFreqMin
Minimum receiver frequency in kHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.6
rFURxFreqMax
Maximum receiver frequency in kHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.7
rFUTxFreqMin
Minimum transmitter frequency in kHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.8
rFUTxFreqMax
Maximum transmitter frequency in kHz
scalarInteger32.1.3.6.1.4.1.17713.8.23.9