managementPortEthernetSpeedStatus
CAMBIUM-PTP800-MIB ·
.1.3.6.1.4.1.17713.8.26.16
Object
scalar
Enumeration
In a 1+1 Hot Standby configuration, the Management Port Ethernet Speed Status attribute indicates if the Ethernet Speed of the Management Port is below that of its neighbor.
Context
- MIB
- CAMBIUM-PTP800-MIB
- OID
.1.3.6.1.4.1.17713.8.26.16- Type
- scalar
- Access
- readonly
- Status
- current
- Parent
- protectionStatus
- Siblings
- 31
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | ok |
1 | lessThanNeighbor |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wirelessReceiveSignalStatus The Wireless Receive Signal Status indicates if the
receiver is able to demodulate the transmit signal from
the remote end of the link. If it cannot demodulate the
signal, a pr… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.10 |
| licensedTransmitCapacityStatus In a 1+1 Hot Standby configuration, the Licensed
Transmit Capacity Status attribute indicates when the
Licensed Transmit Capacity is below that of its
neighbor. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.14 |
| dataPortEthernetSpeedStatus In a 1+1 Hot Standby configuration, the Data Port
Ethernet Speed Status attribute indicates if the Ethernet
Speed of the Data Port is below that of its neighbor. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.15 |
| protectionInterfaceStatus In a 1+1 Hot Standby configuration, information is
shared between neighbor CMUs over the Protection
Interface. The Protection Interface Status attribute
reports whether the nei… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.17 |
| remotePrimaryIPAddress In a 1+1 Hot Standby configuration, the Remote Primary
IP Address reports the IP address of the CMU which is
configured as Primary at the remote end of the wireless
link. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.18 |
| remoteSecondaryIPAddress In a 1+1 Hot Standby configuration, the Remote Secondary
IP Address reports the IP address of the CMU which is
configured as Secondary at the remote end of the wireless
link. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.19 |
| protectionAvailabilityStatus In a 1+1 Hot Standby configuration, the Protection
Availability Status attribute indicates whether the
Active unit is currently being protected by the Inactive
unit. If it isn'… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.2 |
| remotePrimaryMACAddress In a 1+1 Hot Standby configuration, the Remote Primary
MAC Address reports the MAC address of the CMU which is
configured as Primary at the remote end of the wireless
link. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.20 |
| remoteSecondaryMACAddress In a 1+1 Hot Standby configuration, the Remote Secondary
MAC Address reports the MAC address of the CMU which is
configured as Secondary at the remote end of the wireless
link. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.21 |
| remotePrimarySecondaryMode In a 1+1 Hot Standby configuration, this attribute
identifies whether the Active Unit at the remote end of
the link is configured as Primary or Secondary. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.22 |
| transmitterStatus Indicates whether the RFU is transmitting or muted. In a
1+1 Hot Standby configuration, it will also indicate if
the RFU is Inactive and therefore ready to transmit. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.23 |
| endWirelessReceiveSignalStatus The End Wireless Receive Signal Status indicates if the
end of a link is unable to demodulate the signal
transmitted from the remote end of the link. When
Protection is set to … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.26 |
| rxDiversityDataPortStatus When Receive Diversity is enabled, the Inactive CMU
sends Rx Diversity Ethernet Frames to the Active CMU.
Before sending these frames, the Data Port MUST be
negotiated at 1000 … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.27 |
| rxDiversityAvailabilityStatus The Rx Diversity Availability Status attribute will
indicate when Receive Diversity is not operating
correctly, either due to a fault or due to an incorrect
configuration | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.28 |
| rxDiversityConfigurationStatus For Receive Diversity to operate correctly, certain
attributes must be configured correctly on both neighbor
CMUs. The Rx Diversity Configuration Status attribute
will indicate… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.29 |
| protectionConfigurationStatus In a 1+1 Hot Standby configuration, this attribute will
indicate whether the configuration will support
protection. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.3 |
| rxDiversityNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must both be configured with the Protection
attribute set to �1+1 Hot Standby with Rx Diversity�.
The Rx Diversit… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.30 |
| rxDiversityVlanTpidNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must be configured with the same value of
Rx Diversity VLAN TPID. The Rx Diversity VLAN TPID
Neighbor Compatibili… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.31 |
| rxDiversityVidNeighborCompatibility For Receive Diversity to operate correctly, both
neighbor CMUs must be configured with the same value of
Rx Diversity VID. The Rx Diversity VID Neighbor
Compatibility attribute… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.32 |
| neighborInternetAddressType The type of Internet address specified by the associated
neighborInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.33 |
| neighborInternetAddress In a 1+1 Hot Standby configuration, the Neighbor
Internet Address identifies the INET Address of the
neighbor CMU connected via the Protection Interface. | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.34 |
| remotePrimaryInternetAddressType The type of Internet address specified by the associated
remoteSecondaryInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.35 |
| remotePrimaryInternetAddress In a 1+1 Hot Standby configuration, the Remote Primary
Internet Address reports the INET address of the CMU
which is configured as Primary at the remote end of the
wireless lin… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.36 |
| remoteSecondaryInternetAddressType The type of Internet address specified by the associated
remoteSecondaryInternetAddress. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.37 |
| remoteSecondaryInternetAddress In a 1+1 Hot Standby configuration, the Remote Secondary
Internet Address reports the INET address of the CMU
which is configured as Secondary at the remote end of the
wireless… | scalar | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.17713.8.26.38 |
| protectionState In a 1+1 Hot Standby configuration, only one CMU / RFU
at a given end of the link is Active at any one time, the
neighbor CMU / RFU being Inactive. The Protection State
attribu… | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.4 |
| activeUnit At a given end of a 1+1 Hot Standby configuration, one
CMU must be configured as Primary, the other CMU as
Secondary. When a Protected Link initialises with no
faults, the CMU … | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.5 |
| protectionSwitchCause In a 1+1 Hot Standby configuration, the Protection
Switch Cause attribute reports the reason for the last
protection switch. | scalar | Enumeration | .1.3.6.1.4.1.17713.8.26.6 |
| endId In a 1+1 Hot Standby configuration, the End Id contains
the IP address of neighboring CMUs starting with the
highest IP address and with a space separating the
addresses. It is… | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.7 |
| neighborIPAddress In a 1+1 Hot Standby configuration, the Neighbor IP
Address identifies the IP Address of the neighbor CMU
connected via the Protection Interface. | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.17713.8.26.8 |
| neighborMACAddress In a 1+1 Hot Standby configuration, the Neighbor MAC
Address identifies the MAC Address of the neighbor CMU
connected via the Protection Interface. | scalar | OctetString | .1.3.6.1.4.1.17713.8.26.9 |