cadRouteMapNextHop

CADANT-CMTS-POLICY-MIB · .1.3.6.1.4.1.4998.1.1.35.1.30.2.1.11
MIB view Table view

Object

column r/w INET-ADDRESS-MIBInetAddress 
The address of the adjacent next hop router to use in forwading
the matching packet.  The next hop router address must be the 
address of an ajacent router, and the routing table (VRF?) is 
used to verify that the address can be directly reached. Only IPv4
addresses are currently supported.

Context

MIB
CADANT-CMTS-POLICY-MIB
OID
.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.11
Type
column
Access
readwrite
Status
current
Parent
cadRouteMapEntry
Table
cadRouteMapTable
Siblings
18

Syntax

INET-ADDRESS-MIBInetAddress
Source
INET-ADDRESS-MIBInetAddress
Base type
OctetString

Values & Constraints

Type Constraints
range: 0..255

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cadRouteMapId
Id used to associate entries in the policy route map table.
columnInteger32.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.1
cadRouteMapNextHopAddrType
The address type of the next hop and backup next hop addresses. Currently IPv4 is the only supported address type.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.10
cadRouteMapSetBackupNextHop
Indicates whether the backup next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet. This only would be done if the primary ne…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.12
cadRouteMapBackupNextHop
The address type of a second next hop, that can be used only if the primary next hop address can not be reached. Only Ipv4 addresses are currently supported.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.13
cadRouteMapSetNullInterface
If set to true and the packet matches the ACL, it will be dropped.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.14
cadRouteMapRowStatus
The row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createA…
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.15
cadRouteMapSetIpDscp
Indicates whether the IP DSCP should be changed on the packet if it matches the ACL and this is a permit type of match.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.16
cadRouteMapIpDscp
The IP DSCP value that should be used to replace the existing IP DSCP of the matching packet.
columnInteger32.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.17
cadRouteMapSetRecursiveNextHop
Indicates whether the recursive next hop setting should be used to specify the next hop for the remote router when forwarding the matching packet.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.18
cadRouteMapRecursiveNextHop
The address type of a remote router next hop, that is used to perform a recursive route lookup. Only Ipv4 addresses are currently supported.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.19
cadRouteMapSeqNum
Sequence number used to order the match statements.
columnInteger32.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.2
cadRouteMapMatchType
Type of match to used for this entry. Permit matches on the provided ACL and then applies the defined set operations before destination routing. Deny matches on the provided ACL…
columnEnumeration.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.3
cadRouteMapMatchAcl
ACL used to match the incoming packet. Since IPv4 is the only supported address type, the ACL number must be an extended or standard ACL. A value 0 implies that no ACL is used a…
columnInteger32.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.4
cadRouteMapSetIpPrec
Indicates whether the IP Precedence should be changed on the packet if it matches the ACL and this is a permit type of match.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.5
cadRouteMapIpPrec
The IP precedence value that should be used to replace the existing IP precedence of the matching packet.
columnEnumeration.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.6
cadRouteMapSetIpTos
Indicates whether the IP TOS should be changed on the packet if it matches the ACL and this is a permit type of match.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.7
cadRouteMapIpTos
The IP TOS value that should be used to replace the existing IP TOS of the matching packet.
columnEnumeration.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.8
cadRouteMapSetNextHop
Indicates whether the next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.35.1.30.2.1.9