cadIfDownChannelCACL2Threshold
CADANT-CMTS-DOWNCHANNEL-MIB ·
.1.3.6.1.4.1.4998.1.1.15.2.1.1.22
Object
column
r/w
Integer32
Percentage of available bandwidth on the channel that can
be reserved for admitted/active service flows before the
channel goes into Level 2 Overload. When a channel goes
into Level 2 Overload, a warning message will be logged.
Service flow activation/admission will not be denied in
Level 2 Overload.
A channel in Level 2 Overload is a good candidate for
overload control or load balancing actions.
If the percentage is set to 0, the default value will be
used and reading this object must return the the default
L2 threshold.
If a set operation tries to change the value of an
existing instance of this object to any value that
is higher than cadIfDownChannelCACL3Threshold or lower
than cadIfDownChannelCACL1Threshold on the same row, then
an 'inconsistentValue' error must be returned.
Context
- MIB
- CADANT-CMTS-DOWNCHANNEL-MIB
- OID
.1.3.6.1.4.1.4998.1.1.15.2.1.1.22- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cadIfDownstreamChannelEntry
- Table
- cadIfDownstreamChannelTable
- Siblings
- 21
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-1000
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cadIfDownChannelId The Cable Modem Termination System (CMTS) identification
of the downstream channel within this particular MAC
interface. If the interface is down, the object returns
the most curr… | column | Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.1 |
| cadIfCmtsCardNumber Card Number associated with this Channel. | column | CADANT-TCCardId | .1.3.6.1.4.1.4998.1.1.15.2.1.1.19 |
| cadIfDownChannelFrequency The center of the downstream frequency associated with
this channel. This object will return the current tuner
frequency. If this CMTS interface provides IF output only,
this obj… | column | hertz Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.2 |
| cadIfDownChannelCACL1Threshold Percentage of available bandwidth on the channel that can
be reserved for admitted/active service flows before the
channel goes into Level 1 Overload. When a channel goes
into L… | column | Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.21 |
| cadIfDownChannelCACL3Threshold Percentage of available bandwidth on the channel that can
be reserved for admitted/active service flows. A
Registration Request, DSA Request or DSC Request will be
denied due to… | column | Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.23 |
| cadIfDownChannelMaxRoundTripDelay Maximum round-trip propagation delay for cable
plant in Microseconds. Should be configured for
the furthest CM in all cable groups containing
this DownChannel. Default of 1600 M… | column | Microseconds Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.24 |
| cadIfDownChannelAnnex The value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J8… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.15.2.1.1.26 |
| cadIfDownChannelPCNormAllowedUsage Maximum percentage of downstream resources that may be
used by non-emergency telephony services. This is also
the maximum amount of resources non-exclusively allocated
to sess… | column | percent Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.27 |
| cadIfDownChannelPCNormResUsage Minimum percentage of downstream resources that may be
used by non-emergency telephony services. This is also
the maximum amount of resources exclusively allocated
to sessions… | column | percent Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.28 |
| cadIfDownChannelPCEmerAllowedUsage Maximum percentage of downstream resources that may
be used by emergency telephony services. The default
is set from the globals in CadPCMibBase. | column | percent Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.29 |
| cadIfDownChannelWidth The bandwidth of this downstream channel. Most
implementations are expected to support a channel width
of 6 MHz (North America) and/or 8 MHz (Europe). See the
associated complian… | column | hertz Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.3 |
| cadIfDownChannelPCEmerResUsage Minimum percentage of downstream resources that may be
used by emergency telephony services. If the value of
this object is non-zero, then a portion of the downstream
bandwid… | column | percent Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.30 |
| cadIfDownChannelPCTotalAllowedUsage Maximum percentage of downstream resources that may
be used by both normal and emergency telephony services.
The default is set from the globals in CadPCMibBase. | column | percent Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.31 |
| cadIfDownChannelPCPreemptionAllowed Indicates whether the system will preempt another session
for an emergency call. The default is set from the
globals in CadPCMibBase. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.15.2.1.1.32 |
| cadIfDownChannelIfIndex the ifIndex of this downstream channel. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4998.1.1.15.2.1.1.37 |
| cadIfDownChannelPrimaryCapable When a row's cadIfDownChannelPrimaryCapable column is set to true(1)
then DOCSIS SYNC message generation is enabled on the downstream channel.
Otherwise, DOCSIS SYNC message gener… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.15.2.1.1.38 |
| cadIfDownSpectralInversion When a row's cadIfDownSpectralInversion column is set to true(1),
then spectral inversion is enabled. Otherwise, spectral inversion
is disabled. Note that spectral inversion is … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4998.1.1.15.2.1.1.39 |
| cadIfDownChannelModulation The modulation type associated with this downstream
channel. If the interface is down, this object either
returns the configured value (CMTS), the most current
value (CM), or the … | column | Enumeration | .1.3.6.1.4.1.4998.1.1.15.2.1.1.4 |
| cadIfDownChannelInterleave The Forward Error Correction (FEC) interleaving used
for this downstream channel.
Values are defined as follows:
taps8Increment16(3): protection 5.9/4.1 usec,
… | column | Enumeration | .1.3.6.1.4.1.4998.1.1.15.2.1.1.5 |
| cadIfDownChannelPower The CMTS operational transmit power. If this CMTS
interface does not support output power control then
this object will return 0 and be treated as read-only.
If the interface is … | column | dBmV Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.6 |
| cadIfDownChannelPowerFineAdj At the CMTS, the fine power adjustments steps to increase
or decrease the output power in incremental steps. | column | Steps Integer32 | .1.3.6.1.4.1.4998.1.1.15.2.1.1.7 |