cmUsCalBoardType

BRCM-CM-ENGINEERING-MIB · .1.3.6.1.4.1.4413.2.99.1.1.3.2.3.9
MIB view Table view

Object

scalar r/w Enumeration 
Sets the board revision that the tables have been calibrated for; it
helps the app warn the user about incorrect configurations (loading a 
table that has been calibrated for a different modem).  These values 
are the same as those found in the HAL non-vol settings.

Context

MIB
BRCM-CM-ENGINEERING-MIB
OID
.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.9
Type
scalar
Access
readwrite
Status
current
Parent
cmEngrUpstreamCalibration
Siblings
14

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cmUsCalControlStartPower
Controls and reflects the starting power used in the cmUsCalControlTable. Changing this value will result in the size of the cmUsCalControlTable being altered.
scalardBmV Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.1
cmUsCalAmpType
Sets the upstream amp that the tables have been calibrated for; it helps the app warn the user about incorrect configurations. These values are the same as those found in the H…
scalarEnumeration.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.10
cmUsCalAmpGain
Controls and reflects the current value of the amplifier gain, an 8 bit hardware value.
scalarUnsigned32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.11
cmUsCalDacAtten
Controls and reflects the current value of the DAC attenuator, an 8 bit hardware value.
scalarUnsigned32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.12
cmUsCalTransmitNow
When set to cw(1), the device will begin transmitting upstream in CW mode using the specified amp gain and DAC attenuation values. When set to bits23(2), the device will begin tr…
scalarEnumeration.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.13
cmUsCalControlTablePopulate
When set to true(1), the upstream calibration control data will be loaded into the cmUsCalControlTable. If the table is already populated, it will be flushed and re-populated. …
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.14
cmUsCalDiplexerType
Controls and reflects the diplexer type on this board. The primary effect that this setting has is to control the range of frequencies used in upstream calibration when operating…
scalarEnumeration.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.15
cmUsCalControlEndPower
Controls and reflects the ending power used in the cmUsCalControlTable. Changing this value will result in the size of the cmUsCalControlTable being altered.
scalardBmV Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.2
cmUsCalControlResolution
Controls and reflects the resolution used in the cmUsCalControlTable. Changing this value will result in the size of the cmUsCalControlTable being altered.
scalarhundredth dBmV Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.3
cmUsCalZeroControl
If set to true(1), all instances of cmUsCalControlAmpGain and cmUsCalControlDacAtten in the cmUsCalControlTable will be set to a value of zero. When read, always returns false.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.4
cmUsCalControlTable
A list of control values to be used when calculating upstream power for this device.
table-.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.5
cmUsCalOffsetStartFreq
Controls and reflects the starting frequency used in the cmUsCalOffsetTable. Changing this value will result in the size of the cmUsCalOffsetTable being altered.
scalarmegahertz Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.6
cmUsCalOffsetEndFreq
Controls and reflects the ending frequency used in the cmUsCalOffsetTable. Changing this value will result in the size of the cmUsCalOffsetTable being altered.
scalarmegahertz Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.7
cmUsCalOffsetResolution
Controls and reflects the resolution used in the cmUsCalOffsetTable. Changing this value will result in the size of the cmUsCalControlTable being altered.
scalarhundredth megahertz (10 kHz) Integer32.1.3.6.1.4.1.4413.2.99.1.1.3.2.3.8