dot11SSID
BRCM-80211-MGMT-MIB ·
.1.3.6.1.4.1.4413.2.2.2.1.5.1.2
Object
scalar
deprecated
r/w
OctetString
Controls and reflects the service set identifier.
Context
- MIB
- BRCM-80211-MGMT-MIB
- OID
.1.3.6.1.4.1.4413.2.2.2.1.5.1.2- Type
- scalar
- Access
- readwrite
- Status
- deprecated
- Parent
- dot11MgmtBase
- Siblings
- 20
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-32
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dot11OperMode Used to control the 802.11 operational mode. If set to
notAvailable(0), then the wireless interface will be disabled, with
the radio off, and no wireless settings web pages will… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.1 |
| dot1154gNetMode Controls and reflects the behavior of the device with regards to which
flavor of 802.11 is used. If set to mode54gLRS(5), the device
will interoperate with the widest variety of … | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.10 |
| dot1154gProtectionEnable Controls and reflects the state of 54g protection. If set to true(1),
the AP will use RTS/CTS to improve 802.11g performance in mixed
802.11g/802.11b networks. Set to false(2) … | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.4413.2.2.2.1.5.1.11 |
| dot11Rate Forces the transmission rate for the AP to a particular speed. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.12 |
| dot11OutputPower Sets the output power relative to the hardware's maximum capability. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.13 |
| dot11MbssUserControl Sets the number of user controlled Wifi networks.
0 <--- The user has no control over wireless. No 802.11 web pages will be displayed.
For now, we don't need to support t… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.14 |
| dot11BasicRateSet Determines which rates are advertised as BASIC rates in the beacon.
If set to default, the driver defaults for the selected 54gMode will
be used. If set to all, all available rat… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.15 |
| dot11NMode Determines which Mode the N card will run in. Auto Mode will detect which
stations are out there and run in the proper mode, Off Mode will make it such
the card will not run in N … | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.16 |
| dot11NPhyRate Forces the N Phy transmission rate for the AP to a particular speed. Each pair of rates
corresponds to a 20 MHz or 40 MHz channel configuration. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.17 |
| dot11NBand Determines which Band that we will be operating in. Either the 2.4G or the 5G Hz.
Note: This is for N cards only. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.18 |
| dot11NBandWidth Determines which Band Width that we will be operating in. Either the 20MHz or the 40MHz.
Note: This is for N cards only, and this also affect other MIB selections such as dot11NSi… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.19 |
| dot11NSideBand Determines which side Band the channel will operate in.
Note: This is for N cards only, this mib is dependent of what dot11NBandWidth is selected and only
applies when 40MHz is se… | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.20 |
| dot11NProtection Determines if protection will be turned on or off for N mode.
Note: This is for N cards only. | scalar | Enumeration | .1.3.6.1.4.1.4413.2.2.2.1.5.1.21 |
| dot11CurrentChannel Controls and reflects the current channel number (802.11g) or
control channel (802.11n).
If set to (0), the AP will be put in auto-channel mode where
it automatically s… | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.3 |
| dot11BeaconInterval Controls and reflects the beacon interval for the device. | scalar | milliseconds Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.4 |
| dot11DTIMInterval Controls and reflects the DTIM interval for the device. | scalar | milliseconds Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.5 |
| dot11FragThresh Controls and reflects the fragmentation threshold for the device. | scalar | bytes Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.6 |
| dot11RTSThresh Controls and reflects the RTS threshold for the device. | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.7 |
| dot11SRL Controls and reflects the short retry limit for the device. | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.8 |
| dot11LRL Controls and reflects the long retry limit for the device. | scalar | Unsigned32 | .1.3.6.1.4.1.4413.2.2.2.1.5.1.9 |