smCfgCtrlOnResetEnableDisable

Object

column mandatory r/w Enumeration

Switch module configuration control on resets (default and unsolicited).
When set to enabled, the factory default IP configuration will become
active when the I/O module is reset to factory defaults by either the
management module or the I/O module. If an I/O module reset is initiated
by a source other than the management module then the previous IP configuration
will be in affect. In both these cases the MM will lose IP communications with
the IOM.
This MIB object can not be set, if AMM grants switch module the Protected Mode
permission and switch module goes into Protected Mode.
              
 NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional
       (i.e. - 0 and 1 are swapped), however, they cannot be changed since this MIB is already
       published.
              
NOTE: This MIB object is not applicable to modules that are running in Network Address
       Translation (NAT) Mode. A value of disabled(1) will be returned.

Context

MIB: BLADE-MIB
OID: .1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9
Type: column
Access: readwrite
Status: mandatory
Parent: smControlEntry
Table: smControlTable
Siblings: 12

Related Objects

Sibling Objects

Object	Type	Syntax	OID
smControlIndex mandatory Switch module control table index.	column	Integer32	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.1`
smHealthState mandatory The health state for the switch module. 0 = unknown, 1 = good, 2 = warning, 3 = bad.	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.15`
smPMState mandatory The Protected Mode Status for the switch module. standby- Protected Mode capability exists on the IOM but has not been activated on the switch module or the AMM. pending - Protect…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.16`
smPMCtrlEnableDisable mandatory AMM Protected Mode permission for the switch module. disabled - allow AMM to disable Protected Mode Permission for the switch module. enabled - allow AMM to grant Protected Mode P…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.17`
smIOCompatibility mandatory The compatibility status for the I/O module. The possible values and their meanings are as follows: Unknown: This indicates a communication error for the I/O module…	column	OctetString	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.18`
switchModuleControlId mandatory The switch module numeric identifier.	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.2`
smPostResultsAvailable mandatory Describes whether the switch module POST diagnostic result value contained in the smPostResultsValue is valid.	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.3`
smPostResultsValue mandatory The range of values and meanings are as follows: 0x00 - 0x7F ( 0 - 127) Base internal functions 0x80 - 0x9F (128 - 159) Internal interface failures 0xA0 - 0xAF (160 - 175) …	column	OctetString	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.4`
switchModuleMemDiagEnableDisable mandatory Switch module memory diagnostics enabled or disabled. NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional (i.e. - 0 and…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.5`
smCfgCtrlEnableDisable mandatory Switch module configuration control. When set to enabled, only the MM can manage the module. This MIB object can not be set, if AMM grants switch module the Protected Mode permis…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.6`
smExtEthPortsEnableDisable mandatory Switch module external ethernet ports enabled or disabled. This MIB object can not be set, if AMM grants switch module the Protected Mode permission. This MIB object can not be se…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.7`
switchPingRequest obsolete Sends a ping to a switch module's current IPv4 address. This MIB object can not be set, if AMM grants switch module the Protected Mode permission and switch module goes into Prote…	column	Enumeration	`.1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.8`

Object

Context

Syntax

Values & Constraints

Related Objects