serialIfCableDetection

BIANCA-BRICK-SERIAL-MIB · .1.3.6.1.4.1.272.4.25.1.1.11
MIB view Table view

Object

column mandatory r/w Enumeration 
Cable autodetection for:
manual(1)    disabled
auto(2)      serialIfType and serialIfConnector
iftype(3)    serialIfType
connector(4) serialIfConnector

Context

MIB
BIANCA-BRICK-SERIAL-MIB
OID
.1.3.6.1.4.1.272.4.25.1.1.11
Type
column
Access
readwrite
Status
mandatory
Parent
serialIfEntry
Table
serialIfTable
Siblings
27

Syntax

Enumeration

Values & Constraints

Enumerated Values
1manual
2auto
3iftype
4connector

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
serialIfIndex mandatory
Unique interface index of the serial interface.
columnInteger32.1.3.6.1.4.1.272.4.25.1.1.1
serialIfL2Mode mandatory
The layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE the address in a command frame is 0x01, when configured a…
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.10
serialIfCableType mandatory
Show the detected cable type: unknown(1) cable type unknown. x21(2) DB15, X27/V11 (sync) v35(3) M34, V35/V10 (sync) v36(4) DB37,…
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.12
serialIfCableConnector mandatory
Show the detected cable connector type: dte(1) DTE cable dce(2) DCE cable unknown(3) cable type unknown. not-supported(4) cable detection not supported.
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.13
serialIfBundle mandatory
Index of the bundle to aggregate multiple Channels to one interface.
columnInteger32.1.3.6.1.4.1.272.4.25.1.1.14
serialIfL1State mandatory
The serial physical layer state dn(1) physical layer is inactive up(2) physical layer is active
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.15
serialIfSpeedReal mandatory
In DCE/internal clock mode this is the rounded speed in bits per second, because not every baudrate can exactly be generated. In DTE/external clock mode this is the measured speed…
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.16
serialIfLicense mandatory
Shows wether a serial license associated with this serial port port is required, missing or in use.
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.17
serialIfType mandatory
The serial physical interface type none(1) interface disabled x21(2) X21(V11) terminated (sync) v35(3) V35(V11 & V28) (sync) v36(4) V36(V10 & V11) …
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.2
serialIfRxPackets mandatory
Count of received valid Frames.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.20
serialIfRxOctets mandatory
Count of received bytes.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.21
serialIfTxPackets mandatory
Count of transmitted valid Frames.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.22
serialIfTxOctets mandatory
Count of transmitted bytes.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.23
serialIfRxResets mandatory
Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.24
serialIfRxAborts mandatory
Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.25
serialIfRxOverruns mandatory
Count of receiver overruns. If the serial port is unable to grant sufficiently soon/often the bus, the RxFIFO may fill up. This leads to loss of data.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.26
serialIfRxCRCErrors mandatory
Count of corrupted frames. Errors due to interference on the serial cable.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.27
serialIfRxGiantFrames mandatory
Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.28
serialIfTxResets mandatory
Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.29
serialIfConnector mandatory
The physical connector type. When configured as DCE the pins on the output connector act as a DCE interface. If configured as DTE on the output connector act as a DTE interface. …
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.3
serialIfTxAborts mandatory
Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as illegal.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.30
serialIfTxUnderruns mandatory
Count of transmitter underruns. The serial data for the serial port is supplied too slowly.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.31
serialIfTxGiantFrames mandatory
Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size.
columnRFC1155-SMICounter.1.3.6.1.4.1.272.4.25.1.1.32
serialIfLeads mandatory
The value of IfLeads has influence on the state of the physical layer (L1State). When configured as IfLeads=enabled, the state of the physical layer depends on the signals of the …
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.4
serialIfClock mandatory
The physical layer (layer 1) clocking mode. When configured as AUTO the clock provided depends what is configured on connector. If connector is configured as DTE clock must provid…
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.5
serialIfClockEdge mandatory
The value of IfClockEdge influences the (internal) active clock edge(s) for generating/sampling data on the serial line. This value should be left on DEFAULT under normal circu…
columnEnumeration.1.3.6.1.4.1.272.4.25.1.1.6
serialIfSpeed mandatory
The serial interface speed in bits per second. The range is dependant on the type of the line (balanced/unbalanced) and the quality and length of the cable. Over a short distance …
columnInteger32.1.3.6.1.4.1.272.4.25.1.1.8