pmxIfLoopbackMode

BIANCA-BRICK-PMX-MIB · .1.3.6.1.4.1.272.4.12.1.1.8

MIB view Table view

Object

column mandatory r/w Enumeration

Loopback-Mode is only required for equipment test
              
no-loop(1)		do not loopanything, this is the 
			correct mode for normal operation
full-loop(2)		loopback everything incl. the 
			signaling channel
all-channels(3)	loopback all B and D-channels 
only-bchannels(4)	loopback only the B-channels 
              
 The loops are usualy not reversible. Reboot is required
 to regain normal operation mode.

Context

MIB: BIANCA-BRICK-PMX-MIB
OID: .1.3.6.1.4.1.272.4.12.1.1.8
Type: column
Access: readwrite
Status: mandatory
Parent: pmxIfEntry
Table: pmxIfTable
Siblings: 16

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	no-loop
`2`	full-loop
`3`	all-channels
`4`	only-bchannels

Related Objects

Sibling Objects

Object	Type	Syntax	OID
pmxIfIndex mandatory Unique Index of the primary rate interface. The index is similar to slotnumber * 1000 and is also refenced in the ifTable, the isdnIfTable and in the isdnStkTable	column	Integer32	`.1.3.6.1.4.1.272.4.12.1.1.1`
pmxIfPortMode mandatory PortMode switches the CM-PRI's 'Out'-port normal(1) 'Out'-port is disabled, this CM-PRI is connected to 'In' go-thru(2) 'Out'-port is enabled, this CM-PRI i…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.10`
pmxIfSelftest mandatory The result of the initial selftest of the PMX module If the result is not succesful, the module is disabled successful(1) All selftests succeeded; acfa-failure(2)…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.2`
pmxIfLOS mandatory Loss Of Signal conditions since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.21`
pmxIfNoFAS mandatory Loss Of Frame Alignment conditions since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.22`
pmxIfRemoteAlarms mandatory Remote Alarms received since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.23`
pmxIfAlarmInds mandatory Alarms received since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.24`
pmxIfCRC4Errors mandatory CRC4 errors detected since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.25`
pmxIfSlipPositive mandatory Positive Slip conditions detected since startup; flags that the frequency of receive clock is less than frequency of internal system clock	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.26`
pmxIfSlipNegative mandatory Negative Slip conditions detected since startup; flags that the frequency of receive clock is greater than frequency of internal system clock	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.27`
pmxIfLayer1State mandatory The layer 1 state of the primary rate interface active(F1) active, framing and synchronisation is o.k. This is the only state where data-transmission is poss…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.3`
pmxIfLayer1Mode mandatory In T1 and E1 mode the primary rate interface is working with totaly different clock frequencies, framing and impedance. This depends on one of the jumpers on the PMX module. For…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.4`
pmxIfLayer1Framing mandatory In T1 and E1 mode the primary rate interface can work with totaly different framing types on layer 1. The framing type must match the configuration of the first connected poi…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.5`
pmxIfLayer1LineCode mandatory In T1 mode the primary rate interface is able to work with different line codes. e1-hdb3(1) High Density Bipolar 3 Level Coding This is the only valid line…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.6`
pmxIfChannelMode mandatory In T1 and E1 mode the primary rate interface may work with different channel types. Usually every timeslot is similar to one channel but it is also possible to bundle multiple …	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.7`
pmxIfErrors mandatory The measured PMX interface errors since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.9`