pmxIfLayer1Mode

BIANCA-BRICK-PMX-MIB · .1.3.6.1.4.1.272.4.12.1.1.4

MIB view Table view

Object

column mandatory Enumeration

In T1 and E1 mode the primary rate interface is working
with totaly different clock frequencies, framing and 
impedance. This depends on one of the jumpers on the 
PMX module. For correct operation all 5 jumpers must be 
in correct position. 
              
E1 is normaly used in Europe and is similar to 
   PCM30, 30 channels, 2 Mbit/sec, Impedance 120 Ohm 
              
T1 is normaly used in USA and is similar to 
   PCM24, 24 channels, 1.5 Mbit/sec, Impedance 100 Ohm

Context

MIB: BIANCA-BRICK-PMX-MIB
OID: .1.3.6.1.4.1.272.4.12.1.1.4
Type: column
Access: readonly
Status: mandatory
Parent: pmxIfEntry
Table: pmxIfTable
Siblings: 16

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	e1
`2`	t1

Related Objects

Sibling Objects

Object	Type	Syntax	OID
pmxIfIndex mandatory Unique Index of the primary rate interface. The index is similar to slotnumber * 1000 and is also refenced in the ifTable, the isdnIfTable and in the isdnStkTable	column	Integer32	`.1.3.6.1.4.1.272.4.12.1.1.1`
pmxIfPortMode mandatory PortMode switches the CM-PRI's 'Out'-port normal(1) 'Out'-port is disabled, this CM-PRI is connected to 'In' go-thru(2) 'Out'-port is enabled, this CM-PRI i…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.10`
pmxIfSelftest mandatory The result of the initial selftest of the PMX module If the result is not succesful, the module is disabled successful(1) All selftests succeeded; acfa-failure(2)…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.2`
pmxIfLOS mandatory Loss Of Signal conditions since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.21`
pmxIfNoFAS mandatory Loss Of Frame Alignment conditions since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.22`
pmxIfRemoteAlarms mandatory Remote Alarms received since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.23`
pmxIfAlarmInds mandatory Alarms received since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.24`
pmxIfCRC4Errors mandatory CRC4 errors detected since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.25`
pmxIfSlipPositive mandatory Positive Slip conditions detected since startup; flags that the frequency of receive clock is less than frequency of internal system clock	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.26`
pmxIfSlipNegative mandatory Negative Slip conditions detected since startup; flags that the frequency of receive clock is greater than frequency of internal system clock	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.27`
pmxIfLayer1State mandatory The layer 1 state of the primary rate interface active(F1) active, framing and synchronisation is o.k. This is the only state where data-transmission is poss…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.3`
pmxIfLayer1Framing mandatory In T1 and E1 mode the primary rate interface can work with totaly different framing types on layer 1. The framing type must match the configuration of the first connected poi…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.5`
pmxIfLayer1LineCode mandatory In T1 mode the primary rate interface is able to work with different line codes. e1-hdb3(1) High Density Bipolar 3 Level Coding This is the only valid line…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.6`
pmxIfChannelMode mandatory In T1 and E1 mode the primary rate interface may work with different channel types. Usually every timeslot is similar to one channel but it is also possible to bundle multiple …	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.7`
pmxIfLoopbackMode mandatory Loopback-Mode is only required for equipment test no-loop(1) do not loopanything, this is the correct mode for normal operation full-loop(2) loopback everythi…	column	Enumeration	`.1.3.6.1.4.1.272.4.12.1.1.8`
pmxIfErrors mandatory The measured PMX interface errors since startup	column	RFC1155-SMICounter	`.1.3.6.1.4.1.272.4.12.1.1.9`