e3IfLoopback
BIANCA-BRICK-E3-MIB ·
.1.3.6.1.4.1.272.4.42.1.1.12
Object
column
mandatory
r/w
Enumeration
This variable represents the loopback configuration of the E3/DS3 interface. noloop(1) No loopback is configured, normal data is transmitted and received. remoteloop(2) The received data is transmitted again. Receiving works normal. localloop(3) The transmitted data is received Transmitting works normal.
Context
- MIB
- BIANCA-BRICK-E3-MIB
- OID
.1.3.6.1.4.1.272.4.42.1.1.12- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- e3IfEntry
- Table
- e3IfTable
- Siblings
- 22
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | noloop |
2 | remoteloop |
3 | localloop |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| e3IfIndex mandatory The unique interface index of the e3/ds3 interface. | column | Integer32 | .1.3.6.1.4.1.272.4.42.1.1.1 |
| e3IfL2Mode mandatory The X.75 layer 2 mode. This value has influence on the
HDLC address field (first byte of a HDCL frame). When
configured as DTE the address in a command frame is
0x01, when configu… | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.10 |
| e3IfTestPattern mandatory This variable configures which test pattern should be
transmitted.
normal(1) normal data, no test pattern is transmitted.
ones(2) Transmit unframed all ones.
alt-0-1(3) Transmit … | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.11 |
| e3IfBundle mandatory Index of the bundle to aggregate the interface and
channels of other interfaces
to one interface. | column | Integer32 | .1.3.6.1.4.1.272.4.42.1.1.14 |
| e3IfCableLength mandatory 'short' should be used for a cable lenght less then 225 feet.
'long' should be used otherwise. With 'short' the Tx signal is
preattenutated similar to the attenuation of 225 feet… | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.15 |
| e3IfCRCMode mandatory The type of CRC checksum of the HDLC frames.
crc16(1) 16 Bit CRC
crc32(2) 32 Bit CRC | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.16 |
| e3IfL1State mandatory The e3 physical layer state
down(1) physical layer is inactive
up(2) physical layer is active
prbs(3) physical layer is active, a PRBS signal
is detected
nolicense(4) a licens… | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.19 |
| e3IfType mandatory The e3 physical interface type
off(1) interface is switched offline and the
line interface unit is switched off.
e3-unframed(2) Synchronous 34.368 MBit/s fullduplex,
with HD… | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.2 |
| e3IfRxPackets mandatory Count of received valid HDLC Frames. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.20 |
| e3IfRxOctets mandatory Count of received bytes. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.21 |
| e3IfTxPackets mandatory Count of transmitted valid HDLC Frames. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.22 |
| e3IfTxOctets mandatory Count of transmitted bytes. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.23 |
| e3IfRxResets mandatory Count of receiver resets. Under rare circumstances it
might be necessary to reset the receiver to work
properly. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.24 |
| e3IfRxAborts mandatory Count of receiver aborts. The sender of a frame can
indicate a frame as aborted with a special Abort
sequence. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.25 |
| e3IfRxOverruns mandatory Count of receiver overruns. If the e3 port is unable
to grant sufficiently soon/often the bus, the
RxFIFO may fill up. This leads to loss of data. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.26 |
| e3IfRxCRCErrors mandatory Count of corrupted frames. Errors due to interference
on the e3 cable. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.27 |
| e3IfRxGiantFrames mandatory Count of received frames with illegal framesize. This
can occur if a frame delimiter is destroyed. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.28 |
| e3IfTxResets mandatory Count of transmitter resets. Under rare circumstances
it might be necessary to reset the transmitter to work
properly. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.29 |
| e3IfTxAborts mandatory Count of transmitter aborts. While sending a frame it
might be necessary to indicate this frame as aborted. In
this case the receiver regards this frame as illegal. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.30 |
| e3IfTxUnderruns mandatory Count of transmitter underruns. The e3 data for the
e3 port is supplied too slowly. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.31 |
| e3IfTxGiantFrames mandatory Count of transmitted frames with illegal
framesize. This can occur if an upper module creates
packets with more than the maximum allowed packet size. | column | RFC1155-SMICounter | .1.3.6.1.4.1.272.4.42.1.1.32 |
| e3IfClock mandatory The clock source of the E3/DS3 connection.
intern(1) Your router provides the master clock
of the E3/DS3 connection.
extern(2) Your telephone company or the remote
DSU provide… | column | Enumeration | .1.3.6.1.4.1.272.4.42.1.1.5 |