atswitchPortSTPConfig
ATSWTCH2-MIB ·
.1.3.6.1.4.1.207.8.10.3.1.1.9
Object
column
mandatory
r/w
Enumeration
This attribute allows a bridging Mode to be configured with either Spanning Tree enabled or disabled. When Spanning tree is enabled, make sure that this port is belonging to a valid Bridge_id. Spanning Tree is enabled only when a valid Bridge_id is set.
Context
- MIB
- ATSWTCH2-MIB
- OID
.1.3.6.1.4.1.207.8.10.3.1.1.9- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- atswitchPortEntry
- Table
- atswitchPortTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | enable |
2 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| atswitchPortNumber mandatory This object identifies the port of the switch. | column | Integer32 | .1.3.6.1.4.1.207.8.10.3.1.1.1 |
| atswitchPortBridgeid mandatory The Bridge to which this port belongs to . | column | Integer32 | .1.3.6.1.4.1.207.8.10.3.1.1.10 |
| atswitchPortSTPCost mandatory The Cost of the Spanning Tree Protocol.This object is valid only
when STP is enabled. | column | Integer32 | .1.3.6.1.4.1.207.8.10.3.1.1.11 |
| atswitchPortSTPPriority mandatory The Priority of the spanning Tree Protocol. This object is valid when
STP is enabled. | column | Integer32 | .1.3.6.1.4.1.207.8.10.3.1.1.12 |
| atswitchPortSwitchingType mandatory This per-port attribute describes whether the port identified
by atswitchPortNumber uses store-and-forward bridging for local switched
Ethernet packets or cut-through. The Hardwa… | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.13 |
| atswitchPortFlowControlEnable obsolete This Per_port attribute is only for ATS21 product.(81XX).
This per-port attribute describes whether the port
identified has flow Control Enabled or not. Flow Control
on Full Dupl… | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.14 |
| atswitchPortSecurityNumberOfAddresses mandatory This object configures the Max number of addresses at an
instance to be learnt by the device. If the learnt addresses
number is above this number, then the atswitchSecurityAction … | column | Integer32 | .1.3.6.1.4.1.207.8.10.3.1.1.15 |
| atswitchPortName mandatory This attribute associates a user defined string name
with the port. | column | OctetString | .1.3.6.1.4.1.207.8.10.3.1.1.2 |
| atswitchPortAutosenseOrHalfDuplex mandatory This attribute allows an administrative request to
configure whether this port can Autosense or Force the Half Duplex | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.3 |
| atswitchPortLinkState mandatory This attribute allows an administrative request to
read the status of link state on this port. | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.4 |
| atswitchPortDuplexStatus mandatory This attribute allows an administrative request to
read the status of Duplex on this port. | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.5 |
| atswitchPortSpeed mandatory This attribute allows an administrative request to
read/write the speed of this port.
This attribure is read-only for all the Ports on
AT-37XX product .
This Attribute is read… | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.6 |
| atswitchPortState mandatory This attribute allows an administrative request to
disable or enable communications on this port.It also
responds with the status of the port .Except enabled(1) and
disabled(2),… | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.7 |
| atswitchPortTransmitPacingConfig mandatory This Object is supported on AT36XX product line Only.
This attribute allows the transmit Pacing to be enabled or
disabled. | column | Enumeration | .1.3.6.1.4.1.207.8.10.3.1.1.8 |