fsMplsTunnelEndToEndProtection
ARICENT-MPLS-TE-MIB ·
.1.3.6.1.4.1.2076.13.12.1.2.1.8
Object
column
r/w
Bits
This bitmask indicates the level of end to end protection required. A
value of zero (no bits set) indicates that any protection may be
used. The following describes these bitfields:
unprotected
This flag is set to indicate that the LSP should not use any
protection.
fullReroute
This flag is set to indicate that the protecting LSP creation
only when protected (primary) LSP fails.
rerouteWitoutExtraTraffic
This flag is set to indicate that protecting LSP shall not
carry traffic other than that of Primary LSP. In this case
protecting LSP is usually not configured in the data plane
before protected LSP failure.
dedicatedOneToOne
This flag is set to indicate that a dedicated LSP
protection scheme, i.e., 1:1 protection, should be used to
support the LSP.
dedicatedUniOnePlusOne
This flag is set to indicate that a dedicated LSP
protection scheme, i.e., 1+1 protection, should be used to
support the LSP. It is used for protecting uni-directional
tunnel and No additional signalling is required for switching
from one LSP to another in case of failure and recovery
dedicatedBiOnePlusOne
This flag is set to indicate that a dedicated LSP
protection scheme, i.e., 1+1 protection, should be used to
support the LSP. It is used for protecting bi-directional
tunnel and additional signalling is required for switching
from one LSP to another in case of failure and recovery.
Context
- MIB
- ARICENT-MPLS-TE-MIB
- OID
.1.3.6.1.4.1.2076.13.12.1.2.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- fsMplsTunnelEntry
- Table
- fsMplsTunnelTable
- Siblings
- 20
Syntax
Bits
Values & Constraints
Enumerated Values
0 | unprotected |
1 | fullReroute |
2 | rerouteWithoutExtraTraffic |
3 | dedicatedOneToOne |
4 | dedicatedUniOnePlusOne |
5 | dedicatedBiOnePlusOne |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsMplsTunnelType This object allows the administrator to the tunnel type of a MPLS
tunnel.
The value of bit 0 (mpls) if set indicates that this is a normal
MPLS Tunnel.
… | column | Bits | .1.3.6.1.4.1.2076.13.12.1.2.1.1 |
| fsMplsTunnelSrlgType This object indicates shared risk link group value for this tunnel. | column | Enumeration | .1.3.6.1.4.1.2076.13.12.1.2.1.10 |
| fsMplsTunnelIfIndex If mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which corresponds
to an entry in the interfaces table. Otherwise
this variable should contain … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.2076.13.12.1.2.1.11 |
| fsMplsTunnelInitReOptimize This object is used to indicate the Reoptimization of the tunnel. When
this object is set true then user has initiated reoptimization. Default
value of this object is FALSE.
A tun… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.12.1.2.1.12 |
| fsMplsTunnelIsProtectingLsp This object specifies whether this LSP is working LSP or protection
LSP. If this object is set to true, it means the LSP is protection LSP.
If this object is set to false, it mean… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.13.12.1.2.1.13 |
| fsMplsLspTunnelMapIndex This object is used to indicate the tunnel index of FA LSP to which the
tunnel is stacked. This object is applicable only in the node on which
stacking of FA LSP and E2E LSP occurs | column | MPLS-TC-STD-MIBMplsTunnelIndex | .1.3.6.1.4.1.2076.13.12.1.2.1.14 |
| fsMplsLspTunnelMapInstance This object is used to indicate the tunnel instance of FA LSP to which the
tunnel is stacked. This object is applicable only in the node on which
stacking of FA LSP and E2E LSP oc… | column | MPLS-TC-STD-MIBMplsTunnelInstanceIndex | .1.3.6.1.4.1.2076.13.12.1.2.1.15 |
| fsMplsLspTunnelMapIngressLSRId This object is used to indicate the identity of the Ingress LSR of FA LSP
to which the tunnel is stacked. This object is applicable only in the
node on which stacking of FA LSP an… | column | MPLS-TC-STD-MIBMplsExtendedTunnelId | .1.3.6.1.4.1.2076.13.12.1.2.1.16 |
| fsMplsLspTunnelMapEgressLSRId This object is used to indicate the identity of the Egress LSR of FA LSP
to which the tunnel is stacked. This object is applicable only in the
node on which stacking of FA LSP and… | column | MPLS-TC-STD-MIBMplsExtendedTunnelId | .1.3.6.1.4.1.2076.13.12.1.2.1.17 |
| fsMplsTunnelSynchronizationStatus Indicates the Synchronization status of the tunnel upon RSVP-TE Graceful
Restart. This object is applicable only for RSVP-TE signalled tunnels.
Following values are possible.
0. N… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.13.12.1.2.1.18 |
| fsMplsTunnelOutPathMsgId Denotes the message id generated for the PATH message which is sent from the
node.
This is used for recovering the state when the node receives
SRefresh RecoveryPath message fr… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.13.12.1.2.1.19 |
| fsMplsTunnelLSRIdMapInfo This object indicates whether the Ingress and Egress LSR
ID objects of the tunnel entry to be treated as LSR IDs
or should be treated as an index to the fsMplsTpNodeMapTable.
… | column | Bits | .1.3.6.1.4.1.2076.13.12.1.2.1.2 |
| fsMplsTunnelBackupHopTableIndex This object specifies the entry of index into the
mplsTunnelHopTable that hops the explicit route for
backup tunnel when the object fsMplsTunnelEndToEndProtection for the
tunne… | column | MPLS-TC-STD-MIBMplsPathIndexOrZero | .1.3.6.1.4.1.2076.13.12.1.2.1.20 |
| fsMplsTunnelBackupPathInUse This object specifies the entry of index into the
mplsTunnelHopTable that hops the backup path used
for backup tunnel when the object fsMplsTunnelEndToEndProtection for the
tun… | column | MPLS-TC-STD-MIBMplsPathIndexOrZero | .1.3.6.1.4.1.2076.13.12.1.2.1.21 |
| fsMplsTunnelMode This object allows the administrator to configure the mode of
tunnel.
The value unidirectional (0) indicates that the direction of the
tunnel is only single direct… | column | Enumeration | .1.3.6.1.4.1.2076.13.12.1.2.1.3 |
| fsMplsTunnelProactiveSessIndex This object indicates the proactive session index for this tunnel.
When a proactive session to monitor this tunnel is established,
the application updates this object with the ses… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.13.12.1.2.1.4 |
| fsMplsTunnelMBBStatus The administrative Make-Before-Break status for Tunnel.
The value 'enabled' (1) indicates that Tunnel supports
Make-Before-Break capablity.The value 'disabled' (2)
indicates tha… | column | Enumeration | .1.3.6.1.4.1.2076.13.12.1.2.1.5 |
| fsMplsTunnelDisJointType This object indicates the disjoint type of the protection tunnel
with respect to the working tunnel. It is applicable only for
protection tunnel. | column | Enumeration | .1.3.6.1.4.1.2076.13.12.1.2.1.6 |
| fsMplsTunnelAttPointer This variable points to a row in the fsTunnelAttributeTable .
This table identifies the attribute of LSP. A value of zeroDotZero
indicates that no Attribute has been associated wi… | column | SNMPv2-TCRowPointer | .1.3.6.1.4.1.2076.13.12.1.2.1.7 |
| fsMplsTunnelPrConfigOperType This object is used to indicate the operation type/mode of the tunnel.
If the value is set to 'revertive(1)', the normal traffic shall be
returned to the working LSP has recover… | column | Enumeration | .1.3.6.1.4.1.2076.13.12.1.2.1.9 |