fsLaRecTmrDuration
ARICENT-LA-MIB ·
.1.3.6.1.4.1.2076.63.1.20
Object
scalar
r/w
Unsigned32
Sets the duration of the error detection recovery timer.
The timer is started when the error state is detected .
Error is detected when
(i) Port goes to defaulted state.
(ii) Hardware programming fails
(iii) Port is stuck in same state for longer time.
If the value of this timer is 0 ,recovery mechanism is disabled.
Upon expiry of the timer recovery mechanism is initiated .
Context
- MIB
- ARICENT-LA-MIB
- OID
.1.3.6.1.4.1.2076.63.1.20- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- fsLaSystem
- Siblings
- 28
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-3600
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsLaSystemControl Start or shutdown Link aggregation module in the system
When set as 'start', resources required by Link aggregation
module are allocated & Link aggregation module star… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.1 |
| fsLaDLAGSystemID This object is used to configure the global common System identifier in
D-LAG (Active-Active) nodes to be used for communicating with the
peer node when global D-LAG System status… | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.1.10 |
| fsLaDLAGSystemPriority This object is used for configuring global common System priority in
D-LAG (Active-Active) nodes to be used for communicating with
the peer node when global D-LAG System status is… | scalar | Integer32 | .1.3.6.1.4.1.2076.63.1.11 |
| fsLaDLAGPeriodicSyncTime This object is used to configure the D-LAG periodic sync timer
used in Active-Active distributed link aggregation.
Periodic sync timer is used to configure the transmission
interv… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.2076.63.1.12 |
| fsLaDLAGRolePlayed This object is used to hold the current role played by the device
participating in Active-Active distributed LAG.
If role played by node is master, all the port-channel… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.13 |
| fsLaDLAGDistributingPortIndex This object is used to configure the distributing
port on which D-LAG periodic-sync and D-LAG event-update
messages will be sent/received for Active-Active D-LAG internal
communic… | scalar | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.2076.63.1.14 |
| fsLaDLAGDistributingPortList This object is used to configure the distributing
port list on which D-LAG periodic-sync and
D-LAG event-update messages will be sent/received
for D-LAG internal communication bet… | scalar | Q-BRIDGE-MIBPortList | .1.3.6.1.4.1.2076.63.1.15 |
| fsLaMCLAGSystemStatus This object specifies the admin status of Multi-Chassis LAG in
the system. The admin status can be
enabled(1) - Enables MC-LAG in the system
disabled(2) - Disables MC-LAG in the… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.16 |
| fsLaMCLAGSystemID This object is used to configure the global common System identifier in
MC-LAG (Active-Active) nodes to be used for communicating with the
peer node when global MC-LAG System stat… | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.1.17 |
| fsLaMCLAGSystemPriority This object is used for configuring global common System priority in
MC-LAG (Active-Active) nodes to be used for communicating with
the peer node when global MC-LAG System status … | scalar | Integer32 | .1.3.6.1.4.1.2076.63.1.18 |
| fsLaMCLAGPeriodicSyncTime This object is used to configure the MC-LAG periodic sync timer
used in Active-Active Multi Chassis Link Aggregation.
Periodic sync timer is used to configure the transmission
int… | scalar | seconds Unsigned32 | .1.3.6.1.4.1.2076.63.1.19 |
| fsLaStatus Sets the Link aggregation module administrative status as
enabled or disabled. The module can be enabled only when this
object is set to 'enabled'. | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.2 |
| fsLaRecThreshold Sets the threshold counter value after which recovery is triggered.
If the threshold 0 ,recovery mechanism is disabled. Setting a value
for this object configures the f… | scalar | Unsigned32 | .1.3.6.1.4.1.2076.63.1.21 |
| fsLaTotalErrRecCount This object is used to track number of times LA error recovery | scalar | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.1.22 |
| fsLaDefaultedStateThreshold This object is used to track the maximum number of times error recovery
can be triggered from default state. Setting this value will configure the
default threshold on all the por… | scalar | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.2076.63.1.23 |
| fsLaHardwareFailureRecThreshold This object is used to track the maximum number of times error recovery
can be triggered after a hardware failure. Setting this value will configure the
hardware failure recovery … | scalar | Unsigned32 | .1.3.6.1.4.1.2076.63.1.24 |
| fsLaSameStateRecThreshold This object is used to track the maximum number of times the port stays
in the same state before triggering error recovery. Setting this value will
configure the same state recov… | scalar | Unsigned32 | .1.3.6.1.4.1.2076.63.1.25 |
| fsLaRecThresholdExceedAction This object specifies the action to be performed on reaching the recovery
threshold.
When set as none, no action will be performed on reaching the recovery threshold of… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.26 |
| fsLaMCLAGClearCounters This object is used to clear MC-LAG periodic and event update counters
when it is set to TRUE.
Associated MIB objects are
fsLaPortChannelMCLAGPeriodicSyncPduTxCount,
fsLaPortC… | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.63.1.27 |
| fsLaClearStatistics This object is used to clear all the statistics.
When this object is set to TRUE, it will clear the statistics for
the Bridge, port channel and member ports of the port channel. | scalar | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.63.1.28 |
| fsLaMCLAGSystemControl This object start or shutdown Multi-Chassis Link Aggregation Module in the system
start(1) - MC-LAG feature will be enabled in the system.MC-LAG global system status
… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.29 |
| fsLaTraceOption This object is used to enable trace statements in
Link aggregation module.
A four byte integer is used for enabling the level of tracing.
Each bit in the four byte in… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.1.3 |
| fsLaMaxPortsPerPortChannel This object specifies the maximum number of
ports that can attach to a port-channel. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.1.4 |
| fsLaMaxPortChannels This object specifies the maximum number of
port-channels present in the system. | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.1.5 |
| fsLaOperStatus This read only objects gives actual status of the Link
aggregation module (operational status of module). When
module is enabled, Link aggregation protocol starts
functioning. W… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.6 |
| fsLaActorSystemID A 6-octet read-write MAC address value used as a unique
identifier for the System. | scalar | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.1.7 |
| fsLaNoPartnerIndep When enabled, and if there is no remote partner information
available in the system, then the port-channel becomes
operationally down and the member ports of the port-channel
ope… | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.8 |
| fsLaDLAGSystemStatus This object if enabled, will enable Active-Active DLAG in
the system. | scalar | Enumeration | .1.3.6.1.4.1.2076.63.1.9 |