fsLaPortChannelDLAGStatus
ARICENT-LA-MIB ·
.1.3.6.1.4.1.2076.63.2.1.1.18
Object
column
r/w
Enumeration
This object is used to enable or disable the D-LAG
functionality.
This object can be modified irrespective of whether
corresponding port-channel is enabled/disabled.
Configuring D-LAG status to enabled will only enable
load sharing functionality in D-LAG nodes.
Disabling a port-channel will not change/reset the
value of this object but configuring this object to
disabled will disable the D-LAG load sharing
functionality in that D-LAG node.
Configuring this object to enabled will not be allowed
if any of the below mentioned mandatory parameters for
D-LAG are not configured.
1. fsLaPortChannelDLAGSystemID
2. fsLaPortChannelDLAGDistributingPortIndex
or fsLaPortChannelDLAGDistributingPortList
Configuring this object to disabled will not delete
the above mentioned D-LAG mandatory parameters, instead
same configured values will be used when the D-LAG status
is enabled again.
Default value for this object is disabled.
Context
- MIB
- ARICENT-LA-MIB
- OID
.1.3.6.1.4.1.2076.63.2.1.1.18- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- fsLaPortChannelEntry
- Table
- fsLaPortChannelTable
- Siblings
- 42
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | enabled |
2 | disabled |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| fsLaPortChannelIfIndex The ifIndex of the port-channel(Aggregator's
interface index). | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.2076.63.2.1.1.1 |
| fsLaPortChannelMaxPorts This object specifies the maximum number of
ports that can attach to a port-channel. | column | Integer32 | .1.3.6.1.4.1.2076.63.2.1.1.10 |
| fsLaPortChannelSelectionPolicyBitList This object is used to set the link selection policy to be
used by the port-channel.
A four byte integer is used for setting the selecting policy.
Each bit in the four byte intege… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.2.1.1.11 |
| fsLaPortChannelDLAGDistributingPortIndex This object is used to configure the distributing
port on which D-LAG periodic-sync and
D-LAG event-update messages will be sent/received
for D-LAG internal communication between … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.2076.63.2.1.1.12 |
| fsLaPortChannelDLAGSystemID This object is used to configure the common system ID in
D-LAG nodes to be used for communicating with the peer node
when D-LAG status is enabled.
Since all the D-L… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.2.1.1.13 |
| fsLaPortChannelDLAGSystemPriority This object is used for configuring common system priority in
D-LAG nodes to be used for communicating with the peer node when
D-LAG status is enabled.
Since all th… | column | Integer32 | .1.3.6.1.4.1.2076.63.2.1.1.14 |
| fsLaPortChannelDLAGPeriodicSyncTime This object is used to configure the D-LAG periodic sync timer
used in distributed link aggregation.
Periodic sync timer is used to configure the transmission
interval of D-LAG pe… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2076.63.2.1.1.15 |
| fsLaPortChannelDLAGMSSelectionWaitTime This object is used to configure the period for the
master slave selection wait timer used in distributed
link aggregation.
This object is applicable, only if D-LA… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.2076.63.2.1.1.16 |
| fsLaPortChannelDLAGRolePlayed This object is used to hold the current role played by the device
participating in distributed LAG.
This object is applicable, only if D-LAG status and D-LAG
redund… | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.17 |
| fsLaPortChannelDLAGRedundancy This object is used to enable/disable the redundancy feature
in D-LAG node.
When D-LAG redundancy feature is enabled, master-slave-selection
algorithm can be used t… | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.19 |
| fsLaPortChannelGroup An index that uniquely identifies an entry in this table. | column | IEEE8023-LAG-MIBLacpKey | .1.3.6.1.4.1.2076.63.2.1.1.2 |
| fsLaPortChannelDLAGMaxKeepAliveCount This read-only MIB object is used to provide keep alive
mechanism when D-LAG status is enabled.
Each D-LAG node will have a Max Keep alive count and each D-LAG
node maintains sepa… | column | Integer32 | .1.3.6.1.4.1.2076.63.2.1.1.20 |
| fsLaPortChannelDLAGPeriodicSyncPduTxCount This object is used when distributing feature is enabled in a
node to hold the number of periodic-sync PDUs sent on the
distributing port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.21 |
| fsLaPortChannelDLAGPeriodicSyncPduRxCount This object is used when distributing feature is enabled in a
node to hold the number of periodic-sync PDUs received on the
distributing port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.22 |
| fsLaPortChannelDLAGEventUpdatePduTxCount This object is used when distributing feature is enabled in a
node to hold the number of event-update PDUs sent on the
distributing port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.23 |
| fsLaPortChannelDLAGEventUpdatePduRxCount This object is used when distributing feature is enabled in a
node to hold the number of event-update PDUs received on the
distributing port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.24 |
| fsLaPortChannelDLAGElectedAsMasterCount This object is used when distributing feature and redundancy
feature both are enabled in a D-LAG node to hold the number of
times the port-channel has been selected as master. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.25 |
| fsLaPortChannelDLAGElectedAsSlaveCount This object is used when distributing feature and redundancy
feature both are enabled in a D-LAG node to hold the number of
times the port-channel has been selected as slave. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.26 |
| fsLaPortChannelTrapTxCount The number of trap messages sent from the port-channel. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.27 |
| fsLaPortChannelDLAGDistributingPortList This object is used to configure the distributing
port list on which D-LAG periodic-sync and
D-LAG event-update messages will be sent/received
for D-LAG internal communication bet… | column | Q-BRIDGE-MIBPortList | .1.3.6.1.4.1.2076.63.2.1.1.28 |
| fsLaPortChannelMCLAGStatus This object is used to enable or disable the MC-LAG
functionality.
This object can be modified irrespective of whether
corresponding port-channel is enabled/disable… | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.29 |
| fsLaPortChannelAdminMacAddress deprecated This object is used for configuring MacAddress that is
to be used by the port-channel when fsLaPortChannelMacSelection
is force.
WARNING: The value configured should not conflict … | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.2.1.1.3 |
| fsLaPortChannelMCLAGSystemID This object is used to configure the common system ID in
MC-LAG nodes to be used for communicating with the peer node
when MC-LAG status is enabled.
Since all the M… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.2076.63.2.1.1.30 |
| fsLaPortChannelMCLAGSystemPriority This object is used for configuring common system priority in
MC-LAG nodes to be used for communicating with the peer node when
MC-LAG status is enabled.
Since all … | column | Integer32 | .1.3.6.1.4.1.2076.63.2.1.1.31 |
| fsLaPortChannelMCLAGRolePlayed This object is used to hold the current role played by the device
participating in MC-LAG.
Role played by device can be
none(0) - Current role playe… | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.32 |
| fsLaPortChannelMCLAGMaxKeepAliveCount This read-only MIB object is used to provide keep alive
mechanism when MC-LAG status is enabled.
Each MC-LAG node will have a Max Keep alive count and each MC-LAG
node maintains s… | column | Integer32 | .1.3.6.1.4.1.2076.63.2.1.1.33 |
| fsLaPortChannelMCLAGPeriodicSyncPduTxCount This object is used when MC-LAG feature is enabled in a
node to hold the number of periodic-sync PDUs sent on the
ICCL port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.34 |
| fsLaPortChannelMCLAGPeriodicSyncPduRxCount This object is used when MC-LAG feature is enabled in a
node to hold the number of periodic-sync PDUs received on the
ICCL port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.35 |
| fsLaPortChannelMCLAGEventUpdatePduTxCount This object is used when MC-LAG feature is enabled in a
node to hold the number of event-update PDUs sent on the
ICCL port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.36 |
| fsLaPortChannelMCLAGEventUpdatePduRxCount This object is used when MC-LAG feature is enabled in a
node to hold the number of event-update PDUs received on the
ICCL port. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.37 |
| fsLaPortChannelClearStatistics This object is used to clear the statistics of port channel and its member ports.
When this object is set to TRUE, it will clear the statistics for the
port channel and member por… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.2076.63.2.1.1.38 |
| fsLaPortChannelUpCount This object specifies the number of times a portchannel
moves to operational up state. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.39 |
| fsLaPortChannelMacSelection deprecated Indicates the MAC address selection method for
for the port-channel.
Dynamic - System will reserve certain MAC address
for aggregators. These MAC address are
d… | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.4 |
| fsLaPortChannelDownCount This object specifies the number of times a portchannel
moves to operational down state. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.40 |
| fsLaPortChannelHotStandByPortsCount This object specifies the number of hot standby
ports in this port channel entry. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.2076.63.2.1.1.41 |
| fsLaPortChannelOperChgTimeStamp This object specifies the last operational change timestamp
for this port channel. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.2076.63.2.1.1.42 |
| fsLaPortChannelDownReason This object specifies the reason when the portchannel
moves to down state.
operDown(1) - The port is operationally down.
adminDown(2) - The port is shutdown by the user. | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.43 |
| fsLaPortChannelMode Current Operating Channel Mode of the port
Lacp(1) - forcing the port to negotiate with the
partner.
manual(2) - force the port to enable channeling (Manual).
dis… | column | PortLaMode | .1.3.6.1.4.1.2076.63.2.1.1.5 |
| fsLaPortChannelPortCount The number of ports actually configured to the port-channel. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.2.1.1.6 |
| fsLaPortChannelActivePortCount This object will give the number of ports that are attached to the
port-channel and actively carrying data traffic on the link. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.63.2.1.1.7 |
| fsLaPortChannelSelectionPolicy Link selection policy to be used by the port-channel.
Selection policy ISID implies selection based on Service-instance
and is applicable only in provider Backbone bridge. | column | Enumeration | .1.3.6.1.4.1.2076.63.2.1.1.8 |
| fsLaPortChannelDefaultPortIndex The ifIndex of the default port that gets attached to the
aggregator. A value of 0 means there is no default port for
this port-channel.
If this object is set to 0, it will remov… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.2076.63.2.1.1.9 |