ifOOBNode0SecondaryIpAddress
ARICENT-CFA-MIB ·
.1.3.6.1.4.1.2076.27.1.32
Object
Specifies the secondary IP address associated with the OOB interface of Node0
Context
- MIB
- ARICENT-CFA-MIB
- OID
.1.3.6.1.4.1.2076.27.1.32- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- if
- Siblings
- 35
Syntax
SNMPv2-SMIIpAddress
- Source
- SNMPv2-SMIIpAddress
- Base type
OctetString
Values & Constraints
Type Constraints
range: 4
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ifMaxInterfaces deprecated Specifies the maximum number of interfaces that can
be present in the system. | scalar | IF-MIBInterfaceIndex | .1.3.6.1.4.1.2076.27.1.1 |
| ifResetMgmtVlanList A string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanId values
1 through 8; the second octet to VLANs 9 through
16 etc. The most signific… | scalar | OctetString | .1.3.6.1.4.1.2076.27.1.10 |
| ifSecondaryIpAddressTable A list of secondary IP addresses configured over the
interfaces registered with IP.
This table is a extension to the ifMainTable.
The index to this table has th… | table | - | .1.3.6.1.4.1.2076.27.1.11 |
| ifMainExtTable This table is an extension to the ifMainTable. | table | - | .1.3.6.1.4.1.2076.27.1.12 |
| ifCustTLVTable This table allows generic TLV data to be configured per-port.
It may be used to store any port-specific information that
is required by any application. | table | - | .1.3.6.1.4.1.2076.27.1.13 |
| ifCustOpaqueAttrTable This table allows generic integer attributes to be configured
per-port. These attributes will be opaque from ISS's point of
view and will not be processed/understood by ISS. | table | - | .1.3.6.1.4.1.2076.27.1.14 |
| ifBridgeILanIfTable This table is used to read the status of an I-Lan interface
created from Iftable. An I-LAN Interface is
used to create internal connections between bridge ports in a
802.1 devic… | table | - | .1.3.6.1.4.1.2076.27.1.15 |
| ifTypeProtoDenyTable A table to configure the interface types and bridge port types accessible
to various protocol(s). This table will indicate whether
a particular type of interface is to be created… | table | - | .1.3.6.1.4.1.2076.27.1.16 |
| ifmDebug Enables the tracing in the selected submodule in CFA. A 32 bit
integer is used to store the Tracing level in the specified module.
Different Tracing Levels -
BIT 0 - Initiali… | scalar | Unsigned32 | .1.3.6.1.4.1.2076.27.1.17 |
| ifIvrMappingTable This table is used to configure the list of vlans to be
associated for an IVR interface.
The primary Index to this table can only be a IVR interface. | table | - | .1.3.6.1.4.1.2076.27.1.18 |
| ifHCErrorTable A list of interface entries. The number of entries is
given by the value of ifNumber. This table contains
additional objects for the interface table. | table | - | .1.3.6.1.4.1.2076.27.1.19 |
| ifMaxPhysInterfaces deprecated Specifies the maximum number of physical interfaces
that can be present in the system. | scalar | IF-MIBInterfaceIndex | .1.3.6.1.4.1.2076.27.1.2 |
| ifSecurityBridging Enables or Disables Security for Bridged Packets globally. | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.20 |
| ifSetSecVlanList A string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanId values
1 through 8; the second octet to VLANs 9 through
16 etc. The most signific… | scalar | OctetString | .1.3.6.1.4.1.2076.27.1.21 |
| ifResetSecVlanList A string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanId values
1 through 8; the second octet to VLANs 9 through
16 etc. The most signific… | scalar | OctetString | .1.3.6.1.4.1.2076.27.1.22 |
| ifSecIvrIfIndex An Integer which Indicates the IfIndex of IVR Interface used in
Security Processing of Bridged Traffic | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2076.27.1.23 |
| ifAvailableIndexTable This table returns the next available free interface
index for the given interface type | table | - | .1.3.6.1.4.1.2076.27.1.24 |
| ifACTable A list of Attachment Circuit interface related
configurations. Attachment Circuit is a virtual interface
that is a combination of physical port and customer vlan
identifier or it… | table | - | .1.3.6.1.4.1.2076.27.1.25 |
| ifUfdSystemControl The administrative system control status of the Uplink Failure
Detection(UFD) module.
The value 'start' (1) indicates that the Uplink Failure
Detection(UFD) feature should be sta… | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.26 |
| ifUfdModuleStatus This read write objects gives actual status of the Uplink
Failure Detection(UFD).
When Uplink Failure Detection(UFD) is enabled, UFD starts
functioning. When the UFD is disable… | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.27 |
| ifSplitHorizonSysControl The administrative system control status
requested by management for Split Horizon.
The value 'start' (1) indicates that all
resources required for split horizon… | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.28 |
| ifSplitHorizonModStatus The administrative module status requested
by management for Split Horizon.This
enables or disables Split horizon in the
system. A value of 'enabled'(1) indicates
th… | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.29 |
| ifAvailableIndex Shows an ifIndex which is available for creation of
any new virtual (non-physical) interface in the system.
This ifIndex value can be used for creation of interfaces
in the ifMain… | scalar | IF-MIBInterfaceIndex | .1.3.6.1.4.1.2076.27.1.3 |
| ifUfdGroupTable This table contains a list of all the Uplink Failure Detection
(UFD). Group entries in the system.
This table is a extension to the ifMainTable. The index to this
tab… | table | - | .1.3.6.1.4.1.2076.27.1.30 |
| ifLinkUpEnabledStatus This enables or disables Link Up Delay functionality in the System.
A value of 'enabled'(1) indicates that, operational status of the
link is suspended for a configured delay ti… | scalar | Enumeration | .1.3.6.1.4.1.2076.27.1.31 |
| ifOOBNode0SecondaryIpMask Specifies the IP Subnet Mask associted with the
secondary ip address of OOB interface in node0.
If not specified, this object takes the default
subnet mask value based… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.27.1.33 |
| ifOOBNode1SecondaryIpAddress Specifies the secondary IP address associated with the
OOB interface of Node1 | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.27.1.34 |
| ifOOBNode1SecondaryIpMask Specifies the IP Subnet Mask associted with the
secondary ip address of OOB interface in node1.
If not specified, this object takes the default
subnet mask value based… | scalar | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.2076.27.1.35 |
| ifVlanIpTable This table contains L3 interface attributes
that are used for manipulating entries in
various tables.
ifVlanIpTable entry creation, modification and
deletion result… | table | - | .1.3.6.1.4.1.2076.27.1.36 |
| ifMainTable A list of all the interface entries in the system.
This table contains objects which are applicable to all
types of interfaces in the system. This table is a
proprietary extensi… | table | - | .1.3.6.1.4.1.2076.27.1.4 |
| ifIpTable A list of all the interface entries in the system which
are registered with IP.
This table contains objects which are applicable for the
management of IP over the… | table | - | .1.3.6.1.4.1.2076.27.1.5 |
| ifWanTable deprecated A list of all the WAN interfaces in the system.
This table contains objects which are applicable for the
management of WAN interfaces like PPP, MP bundle and
FR/X.25/AT… | table | - | .1.3.6.1.4.1.2076.27.1.6 |
| ifAutoCktProfileTable deprecated A list of all the automatic circuit profiles in the system.
This table contains objects which are useful for configuration
of an automatic circuit profile for a given interface.
… | table | - | .1.3.6.1.4.1.2076.27.1.7 |
| ifIvrTable A list of all the interfaces in the system with IVR related
configurations.
This table is an extension to the ifMainTable. The index to
this table has the semantics of… | table | - | .1.3.6.1.4.1.2076.27.1.8 |
| ifSetMgmtVlanList A string of octets containing one bit per VLAN. The
first octet corresponds to VLANs with VlanId values
1 through 8; the second octet to VLANs 9 through
16 etc. The most signific… | scalar | OctetString | .1.3.6.1.4.1.2076.27.1.9 |