adEShdslProvWireInterfaceMode
ADTRAN-SHDSL-MIB ·
.1.3.6.1.4.1.664.5.59.1.3.1.1.1
Object
column
r/w
Enumeration
This object configures the two-wire or optional four-wire operation for SHDSL Lines.
Context
- MIB
- ADTRAN-SHDSL-MIB
- OID
.1.3.6.1.4.1.664.5.59.1.3.1.1.1- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adEShdslProvEntry
- Table
- adEShdslProvTable
- Siblings
- 23
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | twoWire |
2 | fourWire |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adEShdslProvConstellation This object sets the constellation size for each SHDSL
line. The selected constellation size is rate dependent.
16-TCPAM can only be used for rates ranging from 3 to 60
DS0's (19… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.10 |
| adEShdslProvPowerBackoff This object sets the power backoff value for each SHDSL
line. If 255 is selected, the power backoff will automatically
be applied up to 6 dB. Valid values for forcing the backof… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.11 |
| adEShdslProvName This object sets a display name associated with the selected
SHDSL interface. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.59.1.3.1.1.12 |
| adEShdslProvSpanPower Span power. This is usually NOT applicable to a remote/NCTE unit.
Usually only applies for CO equipment (e.g. an access module). | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.13 |
| adEShdslProvNIUloopback NIU Loopback enable. May not be applicate for all units. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.14 |
| adEShdslProvConstellationCrossoverRate This object defines the rate (in bits per second) at which the number
of bits per symbol used automatically changes from 3 (16-TCPAM) to
4 (32-TCPAM). When the SHDSL line rate re… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.15 |
| adEShdslProvAnfp100KhzLoss This object specifies the customer measured loss at 100Khz on the respective
SHDSL line. When adEShdslProvLineProbing is set to enableANFP(4) this value
sets the maximum rate acco… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.16 |
| adEShdslProvAnfpTargetMargin This object specifies the target SNR margin for a SHDSL line when the ANFP
rate mode has been selected. The SNR margin is the difference between the
desired SNR and the actual SNR… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.17 |
| adEShdslProvEmergencyFreeze This object controls Emergency Freeze operation which provides enhanced
immunity to micro interruptions and short duration overvoltage conditions. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.18 |
| adEShdslProvExtendedFixedRateAndConstellation This object provisions the rate and constellation to be used in Extended Fixed mode.
The first octet contains the rate in 64kbps increments (Nx64k). The second octet contains
the… | column | OctetString | .1.3.6.1.4.1.664.5.59.1.3.1.1.19 |
| adEShdslProvMinLineRate This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(adEShdslSpanMa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.2 |
| adEShdslProvExtendedFixedLastError This object returns the last error encountered during a SET of adEShdslProvExtendedFixedRateAndConstellation. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.59.1.3.1.1.20 |
| adEShdslProvAnfp100KhzLossLetter When adEShdslProvLineProbing is set to enableANFPWorstCase(10)
or enableANFPCurrentCond(11) this object sets the maximum
rate according to the ANFP spec
U (Ultra Short, 100k loss… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.21 |
| adEShdslProvAnfpMaxLineRate This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) when
an ANFP training mode is enabled. The maximum train rate
of the l… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.22 |
| adEShdslProvSCIAlarmThresh This object configures the SCI alarm threshold for adEShdslSCIThreshCrossed in seconds.
A value of 0 means the alarm is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.23 |
| adEShdslProvSCIAlarmSeverity Sets the severity for adEShdslSCIThreshCrossed.
Valid options listed below:
critical (0)
major (1)
minor (2)
alert (3)
info (4) | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.24 |
| adEShdslProvMaxLineRate This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(adEShdslSpanMa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.3 |
| adEShdslProvG9912Annex This object specifies the G991.2 Annex setting for the SHDSL
line. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.4 |
| adEShdslProvCurrCondTargetMargin This object specifies the current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.5 |
| adEShdslProvWorstCaseTargetMargin This object specifies the worst case target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the de… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.6 |
| adEShdslProvUsedTargetMargins Indicates which target SNR margin is enabled currently being used
in line probing. This has no meaning if line probing is disabled. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.7 |
| adEShdslProvClockMode This object configures the clock reference for the STU-C
in a SHDSL Line. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.8 |
| adEShdslProvLineProbing This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate.
… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.9 |