adEShdslProvExtendedFixedRateAndConstellation
ADTRAN-SHDSL-MIB ·
.1.3.6.1.4.1.664.5.59.1.3.1.1.19
Object
column
r/w
OctetString
This object provisions the rate and constellation to be used in Extended Fixed mode.
The first octet contains the rate in 64kbps increments (Nx64k). The second octet contains
the constellation in bits/baud. One thing to note is that DSP hardware version 2.1 has
reduced upper limits. Use adEShdslInvDspHwVersion to retrieve the hardware
version. The valid combinations are as follows:
Constellation Rates(v2.1)
------------- ----------
1 1 - 39(34)
2 2 - 79(69)
3 3 - 119(104)
4 12 - 159(139)
5 15 - 199(174)
6 18 - 239(204)
For example, to set the rate to 120 (7680kbps) and the constellation to 5 bits/baud, the octet
string would be 78 05. If a SET returns an error, perform a GET on adEShdslProvExtendedFixedLastError
for details.
Context
- MIB
- ADTRAN-SHDSL-MIB
- OID
.1.3.6.1.4.1.664.5.59.1.3.1.1.19- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adEShdslProvEntry
- Table
- adEShdslProvTable
- Siblings
- 23
Syntax
OctetString
Values & Constraints
Object Constraints
range: 2-2
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adEShdslProvWireInterfaceMode This object configures the two-wire or optional four-wire
operation for SHDSL Lines. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.1 |
| adEShdslProvConstellation This object sets the constellation size for each SHDSL
line. The selected constellation size is rate dependent.
16-TCPAM can only be used for rates ranging from 3 to 60
DS0's (19… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.10 |
| adEShdslProvPowerBackoff This object sets the power backoff value for each SHDSL
line. If 255 is selected, the power backoff will automatically
be applied up to 6 dB. Valid values for forcing the backof… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.11 |
| adEShdslProvName This object sets a display name associated with the selected
SHDSL interface. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.59.1.3.1.1.12 |
| adEShdslProvSpanPower Span power. This is usually NOT applicable to a remote/NCTE unit.
Usually only applies for CO equipment (e.g. an access module). | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.13 |
| adEShdslProvNIUloopback NIU Loopback enable. May not be applicate for all units. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.14 |
| adEShdslProvConstellationCrossoverRate This object defines the rate (in bits per second) at which the number
of bits per symbol used automatically changes from 3 (16-TCPAM) to
4 (32-TCPAM). When the SHDSL line rate re… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.15 |
| adEShdslProvAnfp100KhzLoss This object specifies the customer measured loss at 100Khz on the respective
SHDSL line. When adEShdslProvLineProbing is set to enableANFP(4) this value
sets the maximum rate acco… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.16 |
| adEShdslProvAnfpTargetMargin This object specifies the target SNR margin for a SHDSL line when the ANFP
rate mode has been selected. The SNR margin is the difference between the
desired SNR and the actual SNR… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.17 |
| adEShdslProvEmergencyFreeze This object controls Emergency Freeze operation which provides enhanced
immunity to micro interruptions and short duration overvoltage conditions. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.18 |
| adEShdslProvMinLineRate This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(adEShdslSpanMa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.2 |
| adEShdslProvExtendedFixedLastError This object returns the last error encountered during a SET of adEShdslProvExtendedFixedRateAndConstellation. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.59.1.3.1.1.20 |
| adEShdslProvAnfp100KhzLossLetter When adEShdslProvLineProbing is set to enableANFPWorstCase(10)
or enableANFPCurrentCond(11) this object sets the maximum
rate according to the ANFP spec
U (Ultra Short, 100k loss… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.21 |
| adEShdslProvAnfpMaxLineRate This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) when
an ANFP training mode is enabled. The maximum train rate
of the l… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.22 |
| adEShdslProvSCIAlarmThresh This object configures the SCI alarm threshold for adEShdslSCIThreshCrossed in seconds.
A value of 0 means the alarm is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.23 |
| adEShdslProvSCIAlarmSeverity Sets the severity for adEShdslSCIThreshCrossed.
Valid options listed below:
critical (0)
major (1)
minor (2)
alert (3)
info (4) | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.24 |
| adEShdslProvMaxLineRate This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(adEShdslSpanMa… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.3 |
| adEShdslProvG9912Annex This object specifies the G991.2 Annex setting for the SHDSL
line. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.4 |
| adEShdslProvCurrCondTargetMargin This object specifies the current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.5 |
| adEShdslProvWorstCaseTargetMargin This object specifies the worst case target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the de… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.59.1.3.1.1.6 |
| adEShdslProvUsedTargetMargins Indicates which target SNR margin is enabled currently being used
in line probing. This has no meaning if line probing is disabled. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.7 |
| adEShdslProvClockMode This object configures the clock reference for the STU-C
in a SHDSL Line. | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.8 |
| adEShdslProvLineProbing This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate.
… | column | Enumeration | .1.3.6.1.4.1.664.5.59.1.3.1.1.9 |