adEShdslProvAnfpMaxLineRate

ADTRAN-SHDSL-MIB · .1.3.6.1.4.1.664.5.59.1.3.1.1.22

Object

column r/w SNMPv2-SMIInteger32

This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) when
an ANFP training mode is enabled.  The maximum train rate
of the line will be the minimum of the ANFP limit rate
(determined by the ANFP 100 Khz Loss Letter), the
ANFP Max Line Rate, and the rate set by Rate Control (if
enabled).

Context

MIB: ADTRAN-SHDSL-MIB
OID: .1.3.6.1.4.1.664.5.59.1.3.1.1.22
Type: column
Access: readwrite
Status: current
Parent: adEShdslProvEntry
Table: adEShdslProvTable
Siblings: 23

Syntax

SNMPv2-SMIInteger32

Source: SNMPv2-SMIInteger32
Base type: Integer32

Values & Constraints

Type Constraints

range: -2147483648..2147483647

Related Objects

Sibling Objects

Object	Type	Syntax	OID
adEShdslProvWireInterfaceMode This object configures the two-wire or optional four-wire operation for SHDSL Lines.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.1`
adEShdslProvConstellation This object sets the constellation size for each SHDSL line. The selected constellation size is rate dependent. 16-TCPAM can only be used for rates ranging from 3 to 60 DS0's (19…	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.10`
adEShdslProvPowerBackoff This object sets the power backoff value for each SHDSL line. If 255 is selected, the power backoff will automatically be applied up to 6 dB. Valid values for forcing the backof…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.11`
adEShdslProvName This object sets a display name associated with the selected SHDSL interface.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.59.1.3.1.1.12`
adEShdslProvSpanPower Span power. This is usually NOT applicable to a remote/NCTE unit. Usually only applies for CO equipment (e.g. an access module).	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.13`
adEShdslProvNIUloopback NIU Loopback enable. May not be applicate for all units.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.14`
adEShdslProvConstellationCrossoverRate This object defines the rate (in bits per second) at which the number of bits per symbol used automatically changes from 3 (16-TCPAM) to 4 (32-TCPAM). When the SHDSL line rate re…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.15`
adEShdslProvAnfp100KhzLoss This object specifies the customer measured loss at 100Khz on the respective SHDSL line. When adEShdslProvLineProbing is set to enableANFP(4) this value sets the maximum rate acco…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.16`
adEShdslProvAnfpTargetMargin This object specifies the target SNR margin for a SHDSL line when the ANFP rate mode has been selected. The SNR margin is the difference between the desired SNR and the actual SNR…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.17`
adEShdslProvEmergencyFreeze This object controls Emergency Freeze operation which provides enhanced immunity to micro interruptions and short duration overvoltage conditions.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.18`
adEShdslProvExtendedFixedRateAndConstellation This object provisions the rate and constellation to be used in Extended Fixed mode. The first octet contains the rate in 64kbps increments (Nx64k). The second octet contains the…	column	OctetString	`.1.3.6.1.4.1.664.5.59.1.3.1.1.19`
adEShdslProvMinLineRate This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (adEShdslSpanMa…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.2`
adEShdslProvExtendedFixedLastError This object returns the last error encountered during a SET of adEShdslProvExtendedFixedRateAndConstellation.	column	SNMPv2-TCDisplayString	`.1.3.6.1.4.1.664.5.59.1.3.1.1.20`
adEShdslProvAnfp100KhzLossLetter When adEShdslProvLineProbing is set to enableANFPWorstCase(10) or enableANFPCurrentCond(11) this object sets the maximum rate according to the ANFP spec U (Ultra Short, 100k loss…	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.21`
adEShdslProvSCIAlarmThresh This object configures the SCI alarm threshold for adEShdslSCIThreshCrossed in seconds. A value of 0 means the alarm is disabled.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.23`
adEShdslProvSCIAlarmSeverity Sets the severity for adEShdslSCIThreshCrossed. Valid options listed below: critical (0) major (1) minor (2) alert (3) info (4)	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.24`
adEShdslProvMaxLineRate This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (adEShdslSpanMa…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.3`
adEShdslProvG9912Annex This object specifies the G991.2 Annex setting for the SHDSL line.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.4`
adEShdslProvCurrCondTargetMargin This object specifies the current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.5`
adEShdslProvWorstCaseTargetMargin This object specifies the worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the de…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.664.5.59.1.3.1.1.6`
adEShdslProvUsedTargetMargins Indicates which target SNR margin is enabled currently being used in line probing. This has no meaning if line probing is disabled.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.7`
adEShdslProvClockMode This object configures the clock reference for the STU-C in a SHDSL Line.	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.8`
adEShdslProvLineProbing This object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate. …	column	Enumeration	`.1.3.6.1.4.1.664.5.59.1.3.1.1.9`