adGenY1731LocalMepLbmSize

ADTRAN-GEN-Y1731-MIB · .1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.15
MIB view Table view

Object

column r/w SNMPv2-SMIInteger32 
Size of the LBM in bytes.  The size encompasses the entire Ethernet 
frame from the header through the FCS.  
              
The supported values are:
0 to indicate Data TLV should not be included in LBM sent.
64 to 2000 bytes to indicate the Data TLV should be included to increase
the frame length to the specified size.
              
If the Data TLV is not included, the LBM will be sent with the minimum
Ethernet frame size of 64-bytes but it will not contain the Data TLV.  A
zero-pad will be used to fulfill  the minimum length requirement.
              
The default value is 0.

Context

MIB
ADTRAN-GEN-Y1731-MIB
OID
.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.15
Type
column
Access
readwrite
Status
current
Parent
adGenY1731LocalMepLbmTransmitEntry
Table
adGenY1731LocalMepLbmTransmitTable
Siblings
15

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
adGenY1731LocalMepLbmStatus
A Boolean flag where true means the MEP is actively sending LBM messages and false means that no LBMs are being transmitted.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.1
adGenY1731LocalMepLbmVlanDropEnable
Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame. For more information about VLAN Drop Enable, please check IEEE 802.1ad.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.10
adGenY1731LocalMepLbmErrorStatus
MEP Loopback error status.
columnSNMPv2-TCDisplayString.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.11
adGenY1731LocalMepLbmTimeout
MEP Loopback Timeout in milliseconds.
columnUnsigned32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.12
adGenY1731LocalMepLbmInterframeDelay
MEP Loopback Interframe Delay in milliseconds.
columnUnsigned32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.13
adGenY1731LocalMepLbmNextTransId
Next transaction identifier to be sent in a Loopback message. This transaction identifier can be zero because it wraps around.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.14
adGenY1731LocalMepValidateData
A Boolean flag where true means the data sent in LBM message has to be validated with the LBR. False indicates no validation is required.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.16
adGenY1731LocalMepLbmConfigStatus
True means the MEP is ready for configuring LBM and a false means the MEP is under LBM configuration. This flag is used to prevent simultaneous configuration by more than one u…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.2
adGenY1731LocalMepLbmDestMacAddress
The Target MAC Address Field to be transmitted. This is a unicast destination MAC address. This address will be used if the value of the column adGenY1731LocalMep…
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.3
adGenY1731LocalMepLbmDestMepId
The MEG End Point Identifier of another MEP in the same MEG to which the LBM is to be sent. This address will be used if the value of the column adGenY1731LocalMepTransmitLbmDestI…
columnInteger32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.4
adGenY1731LocalMepLbmDestIsMepId
True indicates that MEPID of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmi…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.5
adGenY1731LocalMepLbmMessageCount
The number of Loopback messages to be transmitted.
columnInteger32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.6
adGenY1731LocalMepLbmActive
Start or stop LBM transmission. By writing true, start LBM transmisson. By writing false, stop LBM transmission
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.7
adGenY1731LocalMepLbmDataTlv
An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent.
columnOctetString.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.8
adGenY1731LocalMepLbmVlanPriority
The 3 bit priority value to be used in the VLAN tag, if present, in the transmitted frame. The default value is CCM priority.
columnInteger32.1.3.6.1.4.1.664.5.75.2.1.3.3.1.1.9