adGenEthernetDslamFlowRev2MatchSourceMacList
ADTRAN-ETHERNET-DSLAM-FLOW-MIB ·
.1.3.6.1.4.1.664.5.70.2.11.1.74
Object
column
r/w
OctetString
Contains a list of source MAC addresses and mask on which to match
in the following format:
Byte number(s) Description
1 Number of match source MAC address entries (N, 0 to M,
where M = contents of adGenEthernetFlowMatchSourceMacMaxAddresses OID)
2 thru 7 Match source MAC address 1
8 Match source MAC address mask 1 number of bits (1 to 48)
9 thru 14 Match source MAC address 2
15 Match source MAC address mask 2 number of bits (1 to 48)
... ...
7*N-5 thru 7*N Match source MAC address N
7*N+1 Match source MAC address mask N number of bits (1 to 48)
Context
- MIB
- ADTRAN-ETHERNET-DSLAM-FLOW-MIB
- OID
.1.3.6.1.4.1.664.5.70.2.11.1.74- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adGenEthernetDslamFlowRev2Entry
- Table
- adGenEthernetDslamFlowRev2Table
- Siblings
- 74
Syntax
OctetString
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adGenEthernetDslamFlowRev2Index Index that specifies an individual
map. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.1 |
| adGenEthernetDslamFlowRev2DownstreamPbitMapping If the network Pbit mode is mapped then this variable
specifies the ingress/egress priority mapping index. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.10 |
| adGenEthernetDslamFlowRev2NetworkIngressPbit This option is a bitmask used to specify a list of allowable P-bit values
of the S-Tag ingressing from the network. A value of
255 indicates that this value is not used to classif… | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.11 |
| adGenEthernetDslamFlowRev2NetworkIngressEtherType Specify the EtherType value that will be used to
classify NetworkIngress traffic. A value of 0x0000
indicates this filter is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.12 |
| adGenEthernetDslamFlowRev2NetworkIngressDSCP Specify a single DSCP value that will be used to classify
NetworkIngress traffic. A value of 64 indicates this filter
is disabled. If multiple DSCP values should be specified,
us… | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.13 |
| adGenEthernetDslamFlowRev2NetworkIngressIPProtocolID Specify the IP Protocol ID that will be used to
classify NetworkIngress traffic. A value of 0x0000
indicates this filter is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.14 |
| adGenEthernetDslamFlowRev2UpstreamForwardingMode Specify how ethernet frames on this flow are forwarded through the switch. This
value is bitmasked so that forwarding modes can be combined.
src (0x1) - Use the ethernet interface… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.15 |
| adGenEthernetDslamFlowRev2UpstreamSTagPbitMethod Specify the PBit mapping mode in from the
Customer to Network STag.
Inherit - upstream STags should egress
with the priority from the customer.
Marked - upstream STags should a… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.16 |
| adGenEthernetDslamFlowRev2UpstreamSTagPbitMarking If the Customer Pbit mode is marked then this variable
specifies the upstream STag pBit. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.17 |
| adGenEthernetDslamFlowRev2UpstreamSTagPbitMapping If the Customer Pbit mode is mapped then this variable
specifies the ingress/egress STag priority mapping index. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.18 |
| adGenEthernetDslamFlowRev2UpstreamCTagPbitMethod Specify the CTag PBit mapping mode in from the
Customer to Network.
Inherit - upstream traffic should egress
with the priority from the customer.
Marked - upstream traffic shou… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.19 |
| adGenEthernetDslamFlowRev2Name This object is provided so that the user can identify
the ethernet flow uniquely. The profile will be stored in the EMS by
name and applied to the user-specified flows.
This profi… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.2 |
| adGenEthernetDslamFlowRev2UpstreamCTagPbitMarking If the Customer Pbit mode is marked then this variable
specifies the upstream CTag pBit. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.20 |
| adGenEthernetDslamFlowRev2UpstreamCTagPbitMapping If the Customer Pbit mode is mapped then this variable
specifies the ingress/egress CTag priority mapping index. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.21 |
| adGenEthernetDslamFlowRev2CustomerIngressPbit This option is a bitmask used to specify a list of allowable P-bit values
of the CEVlan ingressing from the customer. A value of
255 indicates that this value is not used to class… | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.22 |
| adGenEthernetDslamFlowRev2CustomerIngressEtherType Specify the EtherType value that will be used to
classify CustomerIngress traffic. A value of 0x0000
indicates this filter is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.23 |
| adGenEthernetDslamFlowRev2CustomerIngressDSCP Specify a single DSCP value that will be used to classify
CustomerIngress traffic. A value of 64 indicates this filter
is disabled. If multiple DSCP values should be specified,
u… | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.24 |
| adGenEthernetDslamFlowRev2CustomerIngressIPProtocolID Specify the IP Protocol ID that will be used to
classify CustomerIngress traffic. A value of 0x0000
indicates this filter is disabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.25 |
| adGenEthernetDslamFlowRev2CustomerIngressBroadcast This variable specifies whether or not to
drop CustomerIngress broadcasts on this map. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.26 |
| adGenEthernetDslamFlowRev2CustomerIngressMulticast This variable specifies whether or not to
drop CustomerIngress multicasts on this map. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.27 |
| adGenEthernetDslamFlowRev2CustomerIngressUnicast This variable specifies whether or not to
drop CustomerIngress unicasts on this map. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.28 |
| adGenEthernetDslamFlowRev2CustomerIngressPolicer Indicate which policer to on customer ingress traffic. A value of 0 means no
policer is used on customer ingress traffic. A non-zero value represents
a row from the adGenEthernet… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.29 |
| adGenEthernetDslamFlowRev2TrafficDirection Specify the traffic direction to which this
map applies.
Upstream:
Customer C-Tag, Pbit, Ethertype,
DSCP, and IP Protocol are used to classify traffic
upstream.
The Up… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.3 |
| adGenEthernetDslamFlowRev2EncapsMode Encapsulation mode/type if applicable; 'notApplicable' otherwise. IPoE and PPPoE
specify a particular protocol over ethernet. 'Ethernet' specifies that any protocol over
ethernet … | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.30 |
| adGenEthernetDslamFlowRev2ManualAddrAging Manual Address Aging in minutes for unicast MACs. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.31 |
| adGenEthernetDslamFlowRev2IntermedAgent Enable/disable Intermediate Agent if applicable; 'notApplicable' otherwise. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.32 |
| adGenEthernetDslamFlowRev2DhcpRelay Set the DHCPv4 processing mode:
Enabled(1)- Use DHCPv4 for subscriber authentication
Disabled(2)- Discard DHCPv4
Not Applicable(3)- Unused
Transparent(4)- Ignore DH… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.33 |
| adGenEthernetDslamFlowRev2Option82Insert Enable/disable Option 82 Insertion if applicable; 'notApplicable' otherwise. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.34 |
| adGenEthernetDslamFlowRev2LearnedIpAddrAgingMethod Method for Learned IP Address Aging if applicable; 'notApplicable' otherwise. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.35 |
| adGenEthernetDslamFlowRev2IgmpProcessing Method for IGMP Processing if applicable; 'notApplicable' otherwise. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.36 |
| adGenEthernetDslamFlowRev2IgmpVersion IGMP Version if applicable: v3 implies v1, v2, and v3;
v2 implies v1 and v2; v1 is v1 only; 'notApplicable' otherwise. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.37 |
| adGenEthernetDslamFlowRev2LastMemberQueryInterval Last Member Query Interval in milliseconds.
This is the amount of time between Queries. Low
value results in faster detection of missed leaves. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.38 |
| adGenEthernetDslamFlowRev2LastMemberQueryCount Last Member Query Count. This is the number of
queries before declaring no membership of a group
(channel). | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.39 |
| adGenEthernetDslamFlowRev2NetworkSTag Specify the STag seen on network traffic. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.4 |
| adGenEthernetDslamFlowRev2ImmediateLeave Enable/disable Immediate Leave if applicable; 'notApplicable' otherwise.
Disable is the equivalent of setting Last Member Query Count to 0. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.40 |
| adGenEthernetDslamFlowRev2MaxAllowedMcastGroups Maximum Allowed Non-Guaranteed Multicast Groups. This value is only
considered if multicast groups are enabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.41 |
| adGenEthernetDslamFlowRev2DhcpPPPoERemoteId Enable/disable Remote ID insertion into DHCPv4 Option 82 or
DHCPv6 relay agent in option 37 or PPPoE Vendor Specific tag
if applicable. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.42 |
| adGenEthernetDslamFlowRev2DhcpPPPoELoopCharacteristics Enable/disable loop characteristics insertion into DHCPv4 Option 82 or
DHCPv6 relay agent option 17 (vendor specific) loop characteristics or
PPPoE Vendor Specific tag if applicab… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.43 |
| adGenEthernetDslamFlowRev2DhcpPPPoECircuitIdFormat Used to provision the format of the circuit ID string. This
string is returned by the PPPoE intermediate agent and
DHCP relay agent in v4 sub option 1 or in v6 option 18.
TR-101 s… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.44 |
| adGenEthernetDslamFlowRev2PPPoASessionTimeout Used to set the PPPoA Session timeout when the
mapping is provisioned for PPPoA encapsulation. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.45 |
| adGenEthernetDslamFlowRev2InterfaceIfIndex Specifies the IfIndex of the Interface this mapping is tied to.
If the value is 0 then this map is not applied to a Interface. This
value must be nonzero before the flow can be ac… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.46 |
| adGenEthernetDslamFlowRev2InterfaceLogicalIndex Specifies the logical indes within the ifIndex of the ethernet interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.47 |
| adGenEthernetDslamFlowRev2LastErrorString Returns the reason for the last error. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.70.2.11.1.48 |
| adGenEthernetDslamFlowRev2RowStatus This object is used to create
a new row or modify or delete an
existing map in this table. A row cannot be set to active
until the ethernet interface ifIndex is set. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.664.5.70.2.11.1.49 |
| adGenEthernetDslamFlowRev2NetworkCTag Specify the CTag seen on network ingress/egress traffic. A value of 4095
indicates that no Network CTag is used. A value of 4096 indicates that
that the Network CTag should match… | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.5 |
| adGenEthernetDslamFlowRev2NetworkIngressPolicer Indicate which policer to on network ingress traffic. A value of 0 means no
policer is used on network ingress traffic. A non-zero value represents
a row from the adGenEthernetDs… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.50 |
| adGenEthernetDslamFlowRev2UpstreamDiscard Indicate that any packets matching the upstream criteria will be discarded. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.51 |
| adGenEthernetDslamFlowRev2MaxAllowedMulticastBandwidth Specify the maximum downstream bandwidth(kbps) available for this flow.
This value is only considered if multicast bandwidth is enabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.53 |
| adGenEthernetDslamFlowRev2MaxAllowedMulticastBandwidthEnable When enabled joins for multicast streams by the subscriber are checked to make
sure that the maximum multicast bandwidth will not be exceeded by the join. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.54 |
| adGenEthernetDslamFlowRev2ProfileName This object is provided so that the user can describe a particular flow by any
means desired. This is not related to policers in the adGenEthernetDslamFlowRev2ProfilesTable. | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.55 |
| adGenEthernetDslamFlowRev2MaxAllowedMcastGroupsEnable When enabled joins for multicast streams by the subscriber are checked to make
sure that the maximum number of non-guarenteed multicast groups will not be
exceeded by the join. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.56 |
| adGenEthernetDslamFlowRev2NetworkIngressDSCPList This object is a string used to specify the DSCP values that will
be used to classify NetworkIngress traffic. The DSCP values can
be specified using both list and range notation.… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.70.2.11.1.57 |
| adGenEthernetDslamFlowRev2CustomerIngressDSCPList This object is a string used to specify the DSCP values that will
be used to classify CustomerIngress traffic. The DSCP values can
be specified using both list and range notation… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.70.2.11.1.58 |
| adGenEthernetDslamFlowRev2IgmpRouterIP The source IP address that the DSLAM places in IGMP messages destined
for the subscriber. This value only applies when IGMP is in proxy mode. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.664.5.70.2.11.1.59 |
| adGenEthernetDslamFlowRev2CEVlan Specify the CEVlan seen on customer ingress/egress traffic. A value of 4095
indicates that no CEVlan is present. A value of 4097 indicates that customer traffic can
be tagged or … | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.6 |
| adGenEthernetDslamFlowRev2ActivationStatus Provides an indication of whether the flow is actually activated.
If adGenEthernetDslamFlowRev2RowStatus is not active, this object will
return notActivated. When rowStatus is su… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.60 |
| adGenEthernetDslamFlowRev2ARPProcessing Set the ARP processing mode. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.61 |
| adGenEthernetDslamFlowRev2PPPoEProcessing Set the PPPoE processing mode. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.62 |
| adGenEthernetDslamFlowRev2SubscriberIpRowCreateError Returns the reason for the last row create error
on Subscriber Access Static IP Table. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.70.2.11.1.63 |
| adGenEthernetDslamFlowRev2DhcpPPPoEVendorNumber Used to provision the IANA Enterprise Number.
This Number is returned by the PPPoE intermediate agent and
DHCPv4 relay agent in sub option 9. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.64 |
| adGenEthernetDslamFlowRev2DhcpPPPoEVendorIdFormat Used to provision the format of the vendor ID string. This
string is returned by the PPPoE intermediate agent and
DHCPv4 relay agent in sub option 9. TR-101 states that the
format… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.65 |
| adGenEthernetDslamFlowRev2EvcName Set the name of the EVC that this flow is connected to.
When this object is set, other objects that relate to
EVC parameters (e.g. network S-tag, MAC switching, etc.)
will be chan… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.66 |
| adGenEthernetDslamFlowRev2EvcRoot Indicates whether the mapped interface is connected to the
EVC as a root or a leaf. Root interfaces may forward to
leaves and other roots; leaf interfaces may only forard to
root… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.67 |
| adGenEthernetDslamFlowRev2Dhcpv6Mode Set the DHCPv6 processing mode:
Authenticate(1)- Use DHCPv6 for subscriber authentication
Block(2)- Discard DHCPv6
Transparent(3)- Ignore DHCPv6
Snoop(4)- Process D… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.68 |
| adGenEthernetDslamFlowRev2Dhcpv6RelayAgent Set the DHCPv6 Relay Agent Mode:
enabled(1) - enable the relay agent
disabled(2) - disable the relay agent
sameAsDhcpv4(3) - use the same mode on DHCPv6 Relay Agent as what is pro… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.69 |
| adGenEthernetDslamFlowRev2DownstreamForwardingMode Specify how ethernet frames on this flow are forwarded through the switch. This
value is bitmasked so that forwarding modes can be combined.
src (0x1) - Use the network port as th… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.664.5.70.2.11.1.7 |
| adGenEthernetDslamFlowRev2Dhcpv6RelayAgentTrusted Enable/disable DHCPv6 relay agent trusted mode. | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.70 |
| adGenEthernetDslamFlowRev2DhcpPPPoERemoteIdFormat Used to provision the format of the remote ID string. This
string is returned by the DHCPv4 relay agent in option 82
or DHCPv6 relay agent in option 37 or in PPPoE Vendor Specific… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.71 |
| adGenEthernetDslamFlowRev2DownstreamQosMapProfile The attached QoS Map Profile from the adGenQosMapProfileProvisioningTable
used to classify downstream traffic into egress queues. An empty string
signifies that the default syste… | column | OctetString | .1.3.6.1.4.1.664.5.70.2.11.1.72 |
| adGenEthernetDslamFlowRev2Dhcpv6CurrMode View the current DHCPv6 processing mode:
Authenticate(1)- Use DHCPv6 for subscriber authentication
Block(2)- Discard DHCPv6
Transparent(3)- Ignore DHCPv6
Snoop(4)- … | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.73 |
| adGenEthernetDslamFlowRev2MatchSourceMacLastErrorString Returns the reason for the last error when setting adGenEthernetDslamFlowMatchSourceMacList or
adGenEthernetDslamFlowRev2MatchSourceLastErrorString. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.664.5.70.2.11.1.75 |
| adGenEthernetDslamFlowRev2MatchNonIp Enables/disables matching non-IP customer ingress traffic.
True - enables match non-IP.
False - disables match non-IP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.664.5.70.2.11.1.76 |
| adGenEthernetDslamFlowRev2DownstreamPbitMethod Specify the PBit mapping mode in from the
network to customer.
Inherit - downstream traffic should egress
the Interface with the priority from the
network.
Marked - downstre… | column | Enumeration | .1.3.6.1.4.1.664.5.70.2.11.1.8 |
| adGenEthernetDslamFlowRev2DownstreamPbitMarking If the network Pbit mode is marked then this variable
specifies the downstream pBit. | column | Integer32 | .1.3.6.1.4.1.664.5.70.2.11.1.9 |