adsl2LineCmndAutomodeColdStart
ADSL2-LINE-MIB ·
.1.3.6.1.2.1.10.238.1.1.1.1.6
Object
Automode cold start forced. This parameter is defined
in order to improve testing of the performance of ATUs
supporting automode when it is enabled in the MIB.
Change the value of this parameter to 'true' indicates
a change in loop conditions applied to the devices under
test. The ATUs shall reset any historical information
used for automode and for shortening G.994.1 handshake
and initialization.
Automode is the case where multiple operation-modes are
enabled through the adsl2LConfProfAtuTransSysEna object
in the line configuration profile being used for the
ADSL line, and where the selection of the actual
operation-mode depends not only on the common
capabilities of both ATUs (as exchanged in G.994.1), but
also on achievable data rates under given loop
conditions.
This object MUST be maintained in a persistent manner.
Context
- MIB
- ADSL2-LINE-MIB
- OID
.1.3.6.1.2.1.10.238.1.1.1.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- adsl2LineEntry
- Table
- adsl2LineTable
- Siblings
- 24
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| adsl2LineCnfgTemplate The value of this object identifies the row in the ADSL2 Line
Configuration Templates Table, (adsl2LineConfTemplateTable),
which applies for this ADSL2 line.
This o… | column | OctetString | .1.3.6.1.2.1.10.238.1.1.1.1.1 |
| adsl2LineStatusLastStateDs The last successful transmitted initialization state in
the downstream direction in the last full initialization
performed on the line. | column | ADSL2-LINE-TC-MIBAdsl2LastTransmittedState | .1.3.6.1.2.1.10.238.1.1.1.1.10 |
| adsl2LineStatusLastStateUs The last successful transmitted initialization state in the
upstream direction in the last full initialization performed
on the line. | column | ADSL2-LINE-TC-MIBAdsl2LastTransmittedState | .1.3.6.1.2.1.10.238.1.1.1.1.11 |
| adsl2LineStatusAtur Indicates current state (existing failures) of the ATU-R.
This is a bit-map of possible conditions. | column | ADSL2-LINE-TC-MIBAdsl2LineStatus | .1.3.6.1.2.1.10.238.1.1.1.1.12 |
| adsl2LineStatusAtuc Indicates current state (existing failures) of the ATU-C.
This is a bit-map of possible conditions. | column | ADSL2-LINE-TC-MIBAdsl2LineStatus | .1.3.6.1.2.1.10.238.1.1.1.1.13 |
| adsl2LineStatusLnAttenDs The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during diagnostics mode and initialization. I… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.14 |
| adsl2LineStatusLnAttenUs The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during diagnostics mode and initialization.
It… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.15 |
| adsl2LineStatusSigAttenDs The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime. It ranges from 0 to 1270 uni… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.16 |
| adsl2LineStatusSigAttenUs The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime. It ranges from 0 to 1270 uni… | column | 0.1 dB Unsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.17 |
| adsl2LineStatusSnrMarginDs Downstream SNR Margin is the maximum increase in dB of the
noise power received at the ATU-R, such that the BER
requirements are met for all downstream bearer channels. It
ranges… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.18 |
| adsl2LineStatusSnrMarginUs Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements
are met for all downstream bearer channels. It ranges f… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.19 |
| adsl2LineAlarmCnfgTemplate The value of this object identifies the row in the ADSL2 Line
Alarm Configuration Template Table,
(adsl2LineAlarmConfTemplateTable), which applies to this ADSL2
line.
… | column | OctetString | .1.3.6.1.2.1.10.238.1.1.1.1.2 |
| adsl2LineStatusAttainableRateDs Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by
the ATU-C transmitter and the ATU-R receiver, coded in
bits/second. | column | bits/second SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.20 |
| adsl2LineStatusAttainableRateUs Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in
bits/second. | column | bits/second SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.10.238.1.1.1.1.21 |
| adsl2LineStatusActPsdDs Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub-carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB
(physical… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.22 |
| adsl2LineStatusActPsdUs Actual Power Spectrum Density (PSD) Upstream. The average
upstream transmit PSD over the sub-carriers used for upstream.
It ranges from -900 to 0 units of 0.1 dB (physical values… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.23 |
| adsl2LineStatusActAtpDs Actual Aggregate Transmit Power Downstream. The total amount
of transmit power delivered by the ATU-C at the U-C reference
point, at the instant of measurement. It ranges from -… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.24 |
| adsl2LineStatusActAtpUs Actual Aggregate Transmit Power Upstream. The total amount of
transmit power delivered by the ATU-R at the U-R
reference point, at the instant of measurement. It ranges
… | column | 0.1 dB Integer32 | .1.3.6.1.2.1.10.238.1.1.1.1.25 |
| adsl2LineCmndConfPmsf Power management state forced. Defines the line states to be
forced by the near-end ATU on this line. The various possible
values are:
l3toL0(0),
l0toL2(2), or
l0orL2to… | column | ADSL2-LINE-TC-MIBAdsl2ConfPmsForce | .1.3.6.1.2.1.10.238.1.1.1.1.3 |
| adsl2LineCmndConfLdsf Loop diagnostics mode forced (LDSF). Defines whether the line
should be forced into the loop diagnostics mode by the
near-end ATU on this line or only be responsive to loop
diagn… | column | ADSL2-LINE-TC-MIBAdsl2LineLdsf | .1.3.6.1.2.1.10.238.1.1.1.1.4 |
| adsl2LineCmndConfLdsfFailReason The status of the recent occasion the Loop diagnostics mode
forced (LDSF) was issued for the associated line. Possible
values are:
none(1) - The default value in case … | column | ADSL2-LINE-TC-MIBAdsl2LdsfResult | .1.3.6.1.2.1.10.238.1.1.1.1.5 |
| adsl2LineStatusAtuTransSys The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with only a single bit
set to '1' (the selected coding for the ADSL line). This
parameter may be… | column | ADSL2-LINE-TC-MIBAdsl2TransmissionModeType | .1.3.6.1.2.1.10.238.1.1.1.1.7 |
| adsl2LineStatusPwrMngState The current power management state. One of four possible
power management states:
L0 - Synchronized and full transmission (i.e., Showtime).
L1 - Low Power with reduced net … | column | ADSL2-LINE-TC-MIBAdsl2PowerMngState | .1.3.6.1.2.1.10.238.1.1.1.1.8 |
| adsl2LineStatusInitResult Indicates the result of the last full initialization performed
on the line. It is an enumeration type with the following
values: noFail(0), configError(1), configNotFeasible(2),
… | column | ADSL2-LINE-TC-MIBAdsl2InitResult | .1.3.6.1.2.1.10.238.1.1.1.1.9 |