adslAtucCurrStatus

ADSL-LINE-MIB · .1.3.6.1.2.1.10.94.1.1.2.1.6

Object

column Bits

Indicates current state of the ATUC line.  This is a
bit-map of possible conditions.  The various bit
positions are:
              
0      noDefect             There no defects on the line
              
1      lossOfFraming        ATUC failure due to not
                     receiving valid frame.
              
2      lossOfSignal         ATUC failure due to not
                     receiving signal.
              
3      lossOfPower          ATUC failure due to loss of
                     power.
                     Note: the Agent may still
                     function.
              
4      lossOfSignalQuality  Loss of Signal Quality is
                     declared when the Noise Margin
                     falls below the Minimum Noise
              
                     Margin, or the bit-error-rate
                     exceeds 10^-7.
              
5      lossOfLink           ATUC failure due to inability
                     to link with ATUR.
              
6      dataInitFailure      ATUC failure during
                     initialization due to bit
                     errors corrupting startup
                     exchange data.
              
7      configInitFailure    ATUC failure during
                     initialization due to peer
                     ATU not able to support
                     requested configuration
              
8      protocolInitFailure  ATUC failure during
                     initialization due to
                     incompatible protocol used by
                     the peer ATU.
              
9      noPeerAtuPresent     ATUC failure during
                     initialization due to no
                     activation sequence detected
                     from peer ATU.
              
This is intended to supplement ifOperStatus.

Context

MIB: ADSL-LINE-MIB
OID: .1.3.6.1.2.1.10.94.1.1.2.1.6
Type: column
Access: readonly
Status: current
Parent: adslAtucPhysEntry
Table: adslAtucPhysTable
Siblings: 7

Syntax

Bits

Values & Constraints

Enumerated Values

`0`	noDefect
`1`	lossOfFraming
`2`	lossOfSignal
`3`	lossOfPower
`4`	lossOfSignalQuality
`5`	lossOfLink
`6`	dataInitFailure
`7`	configInitFailure
`8`	protocolInitFailure
`9`	noPeerAtuPresent

Related Objects

Sibling Objects

Object	Type	Syntax	OID
adslAtucInvSerialNumber The vendor specific string that identifies the vendor equipment.	column	OctetString	`.1.3.6.1.2.1.10.94.1.1.2.1.1`
adslAtucInvVendorID The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.	column	OctetString	`.1.3.6.1.2.1.10.94.1.1.2.1.2`
adslAtucInvVersionNumber The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed a…	column	OctetString	`.1.3.6.1.2.1.10.94.1.1.2.1.3`
adslAtucCurrSnrMgn Noise Margin as seen by this ATU with respect to its received signal in tenth dB.	column	tenth dB Integer32	`.1.3.6.1.2.1.10.94.1.1.2.1.4`
adslAtucCurrAtn Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.	column	tenth dB Unsigned32	`.1.3.6.1.2.1.10.94.1.1.2.1.5`
adslAtucCurrOutputPwr Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.	column	tenth dBm Integer32	`.1.3.6.1.2.1.10.94.1.1.2.1.7`
adslAtucCurrAttainableRate Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.	column	bps SNMPv2-SMIGauge32	`.1.3.6.1.2.1.10.94.1.1.2.1.8`